Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
. . . . . . . . . . . . . . . . . . . . 120 V Frequency . . . . . . . . . . . . . . . . . .60 Hz Circuit rating. . . . . . . . . . . . . . . . . . 15 A Appliance dimensions Appliance dimensions Do not install this exhaust hood over cooktops burning solid fuel. When installing the hood, make sure that the following minimum distance (S) between the top of a Miele cooking surface and the bottom of the hood is: -22" (55 cm) above electric cooktops - 26" (65 cm) above gas cooktops - 26" (65 cm) above an open grill For non-Miele cooking appliances maintain the safety distances recommended by the cooktop manufacturer in their installation and operating instructions. If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. See "Warning and Safety instructions" for further information. 26" (65 cm) is recommended for all installations to allow for optimum work space under the hood. Read the entire installation procedures and determine height (S) before beginning the installation. Installation producers differ depending on the model and venting method. If the hood is fitted flush to the ceiling make sure that the remaining distance to the ceiling is not greater or less than appliance height H. Standard unit height H: DA 211 Extraction. . . . . . . . . . . .29 1/8" - 38 9/16" . . . . . . . . . . . . . . . . . . . (740 - 980) mm Recirculation . . . . . . . 32 11/16" - 41 15/16" . . . . . . . . . . . . . . . . . . (830 - 1065 mm) DA 217-3 Extraction . . . . . . . . . . . . .28" * - 37 3/8" . . . . . . . . . . . . . . . . . . . (710* - 950) mm Recirculation. . . . . . . . . .31 1/2" - 40 3/4" . . . . . . . . . . . . . . . . . . (800 - 1035 mm) DA 218 Extraction . . . . . . . . . . . .28 1/8" - 37 5/8" . . . . . . . . . . . . . . . . . . . (715 - 955) mm Recirculation . . . . . . . 31 11/16" - 40 15/16" . . . . . . . . . . . . . . . . . . (805 - 1040 mm) DA 219-3 Extraction. . . . . . . . . . . .28 3/4" - 38 3/16" . . . . . . . . . . . . . . . . . . . (730 - 970 mm) Recirculation . . . . . . . . 32 5/16" - 41 9/16" . . . . . . . . . . . . . . . . . . (820 - 1055 mm) * With air extraction to the rear through a wall the total height must be at least 31 1/8" (790 mm). To fit the chimney, distance A between the top of the chimney and the ceiling must be at least 7/8" (20 mm). Cut out area in wall or ceiling for entrance of 6" (150 mm) ductwork or 5" (125 mm) ductwork with a reducing collar. Appliance dimensions If the standard unit height H is not suitable to the kitchen’s ceiling height, longer optional chimney extensions are available from your Miele dealer or Miele’s Technical Service Department. DA 211 Extraction Recirculation Standard unit H 29 1/8" - 38 9/16 " 740 mm - 980 mm 32 11/16" - 41 15/16 " 830 mm - 1065 mm DATK 217/219 605 38 9/16" - 48" 980 mm - 1220 mm 42" - 51 3/16 " 1066 mm - 1300 mm DATK 217/219 840 48" - 57 1/2 " 1220 mm - 1460 mm 51 3/16" - 60 1/2 " 1300 mm - 1536 mm DA 217-3 Extraction Recirculation Standard unit H 28" - 37 3/8 " 710 mm - 950 mm 31 1/2" - 40 3/4 " 800 mm - 1035 mm DATK 217/219 605 37 3/16" - 46 7/16 " 945 mm - 1180 mm 40 3/4" - 50" 1035 mm - 1270 mm DATK 217/219 840 46 7/16 " - 55 11/16 " 1180 mm - 1414 mm 50" - 59 1/4 " 1270 mm - 1505 mm Appliance dimensions DA 218 Extraction Recirculation Standard unit H 28 1/8" - 37 5/8 " 715 mm - 955 mm 31 11/16" - 40 15/16 " 805 mm - 1040 mm DATK 217/219 605 37 5/8" - 47" 955 mm - 1195 mm 41" - 50 3/16 " 1041 mm - 1275 mm DATK 217/219 840 47" - 56 1/2 " 1195 mm - 1435 mm 50 3/16 - 59 1/2 " 1275 mm - 1511 mm DA 219-3 Extraction Recirculation Standard unit H 28 3/4" - 38 3/16 " 730 mm - 970 mm 32 5/16" - 41 9/16 " 820 mm - 1055 mm DATK 217/219 605 38 3/16" - 47 5/8 " 970 mm - 1210 mm 41 9/16" - 50 13/16 " 1056 mm - 1290 mm DATK 217/219 840 47 5/8 " - 57 1/16 " 1210 mm - 1450 mm 50 13/16" - 60 1/16 " 1290 mm - 1526 mm Installation Retaining plates Attaching the retaining plates to the wall The ventilation system will be mounted to the wall through the use of retaining plates. Plate A is installed first, followed by plate B. Plate C should only be used if the distance between plate A and plate B is greater than 14 3/8" (365 mm). ^ Before fitting the retaining plate draw a vertical line centrally above the cooktop on the rear wall. ^ Mark measurement S from the cooktop surface upwards (see "Appliance dimensions"). This marks the height of the lower rim of the hood. Installation Retaining plate A ^ Drill two 1/8" (3 mm) holes, one at S + 4" (100 mm) and one at S + 16 3/4" (425 mm) on the center line for the retaining plate (see "Appliance dimensions"). ^Lightly secure retaining plate A into position using 5 x 40 mm screws through the two holes and use the notches to align with the center line. ^ Drill 4 more 1/8" (3 mm) holes through the now fitted retaining plate. ^ Screw two 5 x 40 mm screws into the upper two holes. Retaining plate B ^ Hold retaining plate B to the wall an...
Ce manuel est également adapté pour les modèles :Ventilateurs - DA217-3 (966.24 kb)