Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0,9 m) from the front and top of the heater and keep them away from the sides and rear. 4. Extreme caution is necessary when any heater is used by or near children and whenever the heater is left operating and unattended. 5. Always unplug heater when not in use. 6. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. If heater has leaked any oil, discontinue using the heater and contact the service center as indicated in the instruction leaflet. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair. 7. Do not use outdoors. 8. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over. 10. To disconnect heater, turn controls to off, then remove plug from outlet. 11. Connect to properly polarized outlets only. 12. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage the heater. 13. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 14. A heater has hot or arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. 15. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. 16. To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet (receptacle) or into another outlet (receptacle) wired into the same circuit. 17. It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging heater into a worn outlet /receptacle/ may result in overheating of the power cord or fire. 18. Do not use an extension cord because it may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 1 4 AWG minimum size and rated not less than 1875 watts, and has to be used only for supplying power to this heater. 19. Be sure that the plug is fully inserted into an appropriate outlet. Please remember that outlets also deteriorate due to aging and continuous use: check periodically if signs overheating or deformations are evidenced by the plug. Do not use the outlet and CALL your electrician. 20. Check that neither the appliance nor the power cable have been damaged in any way during transportation. 21. Make sure that no pieces of polystyrene or other packaging material have been left between one element of the appliance and another. It may be necessary to pass over the appliance with a vacuum cleaner. 22. When switching on the appliance for the first time, allow it to run at full power for about two hours to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated during this operation. It is normal for the appliance to emit small cracking sounds when you turn it on for the first time. 23. CAUTION: to prevent electric shock match wide blade of plug to wide slot, fully insert. 24. Do not cover the appliance while it is functioning in order to avoid overheating with the attendant risk of fire. SAVE THESE INSTRUCTIONS ELECTRICAL CONNECTION Before using the appliance check that your supply voltage is the same of that shown on the rating label of the unit. INSTALLATION The appliance can be used on any horizontal surface. Do not overload the electrical circuit. Avoid using the same socket for other appliances. OPERATION AND USE 1. Make sure the appliance is off before plugging into the mains. 2. Plug the appliance, the pilot lamp will light on. 3. Turn the appliance on by placing the thermostat (C) in the Max position and the mode selector (A) in one of the following positions: 1/2. -Summer operation (fan only): turn the mode selector to the position. -Minimum power setting: turn the mode selector (A) to the "1" position. - Maximum power setting: turn the mode selector (A) to the "2" position. HOW TO TURN THE APPLIANCE OFF To turn the appliance off turn the mode selector (A) to the "." position. Adjusting the thermostat When the room has reached the required temperature, turn the thermostat slowly the anti-clockwise direction until you hear a click. The thermostat will then keep room temperature at the selected level automatically. Fr...