5 Extractor version ................................................................................ 5 Filter Version ...................................................................................... 5 Control Panel - 8160 D - 8190 D - 8260 D - 8290 D .......................... 6 Control Panel - 8360 D - 8390 D - 8361 D - 8391 D .......................... 7 Maintenance and care ...................................................................... 8 Cleaning the hood .......................

2. Nettoyez Ia carrosserie interieure uniquement avec de I’eau chaude additionnee de liquide a vaiselle (n’utilisez pas de detergents agressifs, de brosses ou de poudres abrasives). • Lors de la commande d’un filtre de rechange, veuillez preciser la designation du modele et la reference du produit. Ces donnees sont indiquees sur la plaque signaletique a l’interieur de l’appareil. • Vous pouvez commander le filtre a charbon aupres de votre magasin vendeur. Fig. 3 Attention • Il y a risque d’incen

This operation is necessary after approximately 160 working hours. (Please see page 13 for instructions on Cleaning/replacing). Resetting the saturation indicator After cleaning the filters, press button A for 3 seconds until the grease filter LED D or the activated charcoal filter LED E stops flashing. Maintenance and care • The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter • The purpose of the grease filters is to aspira

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: WARNING: DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED. MAKE SURE ELECTRICAL SERVICE TO THE FAN IS LOCKED IN OFF POSITION. 1. Read all instructions before

Additional wires will be present. 4. Carefully tuck wires back inside wire compartment and replace wire compartment cover securing with the screw that was removed earlier. SECTION 6 Completing the Installation 1. If the fan’s blower assembly was removed during the wiring process, reinstall the blower by reversing the directions in Step 1bin Section 5 Wiring. 2. Plug the fan’s quick connect motor cord into the receptacle. This cord will only fit one way into the receptacle (Figure 9). Figure 9 3.

NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD. Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal

(Figure 4-Detail A) New 3/04 OPERATING INSTRUCTIONS 1.)TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor: First pull: High Second pull: Medium Third pull: Low Fourth pull: OFF NOTE: This fan is very heavy. Failure to securely hold onto head assembly while adjusting head height or head angle could result in personal injury. 2.)TO ADJUST HEAD ANGLE: While holding head firmly, loosen knob under motor (turn counterclockwi

5 Maintenance and cleaning Before doing any maintenance work on the hood, disconnect it from the main supply by disconnecting the plug from the wall socket or unscrewing the fuse. Cleaning the hood Clean the outside of the hood using a damp cloth and a mild detergent. Never use corrosive, abrasive or flammable cleaning products. Cleaning the grease filters Clean the filter every month or every other month according to how much the hood is used. The cleaner the filters, the more grease they colle

Following the proper mounting diagram, attach the Bracket to the stud using three (3) 5/16" diameter x 2" long Lag Screws (Not Supplied) or appropriately sized Bolts and Nuts if attaching to "I" beams. Wall Mount Assembly (Figure 2) Ceiling Mount Assembly (Figure 3) Insert Bolt through Yoke, Bracket, Pivot Hole, Flatwasher, and into Locknut. (Figure 2) or (Figure 3) While holding Fan in the desired position, firmly tighten the 7/16" Bolt. Figure 2 (Wall Mount Assembly) Fan Head Nut Wall Stud Fig