Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
JAN f 19d6 1 EMPTY press Second press It will take several seconds for the tape remaining indicator to operate after the tape starts moving. Recording the Date and Time Set the POWER switch to CAMERA. When placed in Record mode, the time and date will be recorded on the tape. Third 1XBQMB pjc press «■ k--------* ^ JAN 1 199« j SP REC 12:00:00AM JAN 1 1fl94 Press DISPLAY twice to change the display to date only. Press once or twice more to remove the date/ time display. Note: [Only the Date and/or Time indications are recorded on the Tape. | Display-Off Mode This feature allows you to remove all Electronic Viewfinder/LCD Monitor Indications except Intelligent Titler (see pages 38-40). Before inserting a tape, press DISPLAY and STOP together for more than one second to remove the indications except time and date*. To display the Electronic Viewfinder Indications again, turn the Camcorder Power off and then on again. * To remove the time and date, press the DISPLAY button repeatedly. 18 Electronic ViewfinderILCD Monitor Indications © © [23711 ir H isbimfiq] VCR-MODE 1 2:00:00AML JAN 1 1998 I F A D El © Battery Remaining Indication (see page 18) When a battery recharge is necessary, “WARNING LOW BATTERY” will appear in the EVF. The external Power Lamp will start to flash and the Camcorder will automatically turn OFF in 15 seconds. © Tape Remaining Indication • If the Camcorder is in the camera mode, (RECORD) with no cassette tape inserted, or the record tab is missing, “(SI" will flash for one minute and “CHECK TAPE” will appear for 5 seconds. • As the tape reaches the end during recording, “E3” will flash and “TAPE END” will appear lor 5 seconds as a warning. (3) 10-Second Reminder An elapsed time indicator appears one second for every 10 seconds that recording continues. This is a reminder of how long you have been shooting a particular scene and can help keep your recordings fresh and interesting. 0:00 0:10 0:20 ..... 59:50 ^_I • The 10-Second Reminder will reset to 0:00 (return to 0:00 and continue) whenever you press the RECORD/PAUSE © TAPE SPEED Indication (see page 12) Indicates the tape speed (SP or SLP or T.LAPSE). (D Operating Mode Indications REC (record) (Appears in large then small characters.) PAUSE (Appears in large then small characters.) FF (fast forward) PLAY REW (rewind) button. 19 Getting Started Electronic ViewfinderILCD Monitor Indications © Zoom Magnification leve! (see page 32). 0 High Speed Shutter Indication (see page 34). (D VCR-MODE Indication Appears for one minute if the POWER switch is set to VCR or the RECORD/PAUSE button is pushed in VCR MODE. ® DEW Indication If excessive moisture condenses in the unit, “WARNING DEW DETECTED” will appear, Power Lamp will flash, and the Camcorder will automatically turn OFF in 15 seconds. Wait until the indicator no longer flashes when your Camcorder is turned on before use. (0) Time Lapse Indication (see page 36). (0) Date and Time Indication (see page 16). © Backlight Indication (see page 32). © Manual Focus Indication (see page 33). (Q) Light ON/OFF Indication (see page 22). @ Fade Indication (see page 35). 20 Attaching the Shoulder Strap Make sure the Battery Pack is not attached. Undo the two strap ends from their buckles. Thread the strap ends through the Strap Attachment Rings. min. 1 inch (25.4mm) Adjusting the Length 3Reinsert the strap ends through their buckles. * Make sure the straps are not twisted. 1 Pull a loop of the strap loose from the buckle. 2Pull the strap firmly through the buckle to shorten or lengthen the strap. Adjust the length of the Hand Strap to the size of your hand as illustrated. 21 Getting Started Built-in Auto Light Using the Built-in Auto Light To improve recording indoors or outdoors in dim lighting conditions. DANGER: When replacing the bulb, use only lamp bulbs (PART NO. VLLW0015) supplied by Panasonic to reduce the risk of fire. Use a cloth or tissue when handling the bulb as finger oils will decrease the bulb life. To prevent possible burn hazard, remove the lens cover and allow the lamp to cool before Before you begin... • Connect the Camcorder to a power source. • Set the POWER switch to CAMERA. Set the LIGHT switch to AUTO. The built-in light automatically turns on and off depending on lighting conditions. Or set LIGHT to ON/OFF to turn the light on and off manually. will appear in the EVF while the light is turned on. Caution: This light becomes hot during operation. Make sure nothing covers the Light during operation. Before you begin... • Set the POWER switch to OFF. • When ordering replacement bulbs, use PART No. VULS0001 1 Push in on the both sides of the lens cover to unlock and pull it straight out from the Camcorder. ^Using Tweezers or Needle-nose pliers, carefully remove the bulb from the Camcorder. • If you have trouble replacing the bulb, please take the unit to your nearest service cent...