Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
VQT1D97 Others If you drop the battery accidentally, check to see if the terminals are damaged. .Attaching a battery with damaged terminals can damage the unit. Do not throw old batteries into fire. .Heating a battery or throwing it into a fire may result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery. About the AC adaptor .If the temperature of the battery is extremely high or extremely low, charging may take time or the battery may not be charged. .Be sure to use the supplied AC adaptor. .If you use the AC adaptor near a radio, radio reception may be disturbed. Keep the AC adaptor 1 m (3.3 feet) or more away from the radio. .When using the AC adaptor, it may generate whirring sounds. However, this is normal. .After use, be sure to disconnect the AC adaptor. (If it is left connected, about 0.1 W of current is consumed at most.) .Always keep the electrodes of the AC adaptor and battery clean. Put this unit near the outlet to make it easy for the interrupting device (plug) to reach it. About the SD card .The memory capacity indicated on the label of an SD card is the total of the capacity for copyright protection and management and the capacity which can be used on the unit, a computer etc. .During prolonged use, the unit’s surfaces and the SD card will heat up slightly. This is normal. When inserting or removing the SD card, always set the mode dial to OFF. While this unit accesses the SD card (while is being displayed/the access lamp is lit), do not open the card/battery door and remove the SD card, operate the mode dial, turn off the power, or shake or impact the unit. . About the miniSD Card .Be sure to insert miniSD Cards in the designated card adaptor before use. Inserting a card in this unit without the adaptor may damage the unit or the card. .Do not insert an empty card adaptor in this unit. Do not leave the adaptor in this unit while inserting or removing miniSD Cards. This may cause the unit to malfunction. VQT1D97 Others LCD monitor .When the LCD monitor gets dirty, wipe it with a dry soft cloth. .In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with a soft dry cloth. .When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the power is turned on. The normal brightness will be restored when the unit’s internal temperature rises. Extremely high precision technology is employed to produce the LCD Monitor screen featuring a total of approximately 123,000 pixels. The result is more than 99.99% effective pixels with a mere 0.01% of the pixels inactive or always lit. However, this is not a malfunction and does not affect the recorded picture. About condensation If condensation forms on the unit, the lens will cloud up, the SD card may be damaged and the unit may not work properly. Make every effort to ensure that condensation does not form. If it does form, take the actions described below. . Causes of condensation Condensation takes place when the ambient temperature or humidity is changed as follows. .When this unit is brought inside from the cold (e.g. a ski slope) to a warm room. .When this unit is moved from an air-conditioned car to outside. .When a cold room has been warmed up quickly. .When cool wind from an air conditioner is directly blown onto this unit. .After summer afternoon rain showers. .When this unit is in a very humid place where the air is thick with steam. (e.g. a heated swimming pool) When this unit is taken to a location with a significant temperature difference such as from a cold place to a hot place. If, for example, you have used this unit for recording on a ski slope and are taking it into a heated room, place the unit inside a plastic bag, remove as much of the air from inside the bag as possible, then seal the bag. Leave the unit for about an hour in the room so the temperature of the unit is close to the ambient temperature of the room, then use it. . What to do if the lens is fogged up. Remove the battery or AC adaptor and leave the unit for about 1 hour with the card/battery door open. When the unit becomes close to the ambient temperature, the fog disappears naturally. VQT1D97 Others Explanation of terms Automatic white balance White balance adjustment recognizes the color of light and adjusts so the white color will become a purer white. The unit determines the hue of light that comes through the lens and white balance sensor, thereby judging the recording condition, and selects the closest hue setting. This is called automatic white balance adjustment. However, since the unit only stores white color information under certain light sources, automatic white balance adjustment does not function normally under other light sources. 2) 1) 10 000K 9 000K 8 000K 7 000K 6 000K 5 000K 4 000K 3 000K 2 000K 1 000K 3) 4) 5) 6) 7) 8) 9) 10) T...