Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Proceed as follows: (1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed). (2) While pressing both €3 and , press CU for a few seconds. The message ALL RESET momentarily appears on the monitor. This resets all adjustments and parameters to the factory default settings. 9- • Editing the CAM SET UP Menu Important Notice: When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent accidental changing of the settings. To edit the CAM SET UP menu (change settings), press êï and ^ or d and to move the cursor to SET UP DISABLE in the bottom line. Press El. SET UP DISABLE changes to SET UP ENABLE. Move the cursor to END, then to the item{s) you want to change. '-\ ** CAM SET DP •* CAMERA ID OFF “1 ALC/ELC ALC 1 SHUTTER OFF AQC ON (DNR-H) SENS UP OFF SYNC I NT WHITE BAL ATW1 1 MOTION DET OFF LENS DRIVE DC BHD * SETUP disable ^ ......r~ ............. ** CAM BET DP *• CAMERA ZD OFF ~1 ALC/ELC ALC 1 SHUTTER OFF AGC ON (DNR-H) SENS DP OFF SYNC INT WHITE BAL ATW1 ~l MOTION DET OFF LENS DRIVE DC END -20- Important Notice: When the cursor is moved to END and the CAM SET UP menu closed after changing the parameters, the new values are saved in the EEPROM (Electric Erasable and Programmable Read Only Memory). These values remain valid until new values are saved, even if the power of the camera is off. SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or oft on the monitor screen. - ** CAM SET UP ** CAMERA ID [OFF, "I ALC/ELC ALC "I SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 1 MOTION DET OFF LENS DRIVE DC END SET UP ENABLE v To edit the CAMERA ID 1. Move the cursor to the CAMERA ID parameter. 2. Press [=] • The CAMERA ID menu appears. The cursor on the letter "0" is highlighted. Pointer Character Cursor A, 0123456789 ABCDKFGHI iJKXiM NOPQRSTUVWXTZ (>.,•■:)*#!?-+-*/*$ SPACE POSI RET END RESET Character Area Command Editing Area CAMERA ID menu 3. Move the cursor to the character you want to edit by pressing €1/. 4. After selecting the character, press GO. The selected character appears in the editing area. (The pointer in the editing area moves to the right automatically at this moment.) 5. Repeat the steps above until all characters are edited. To enter a blank space in the CAMERA ID Move the cursor to SPACE and press El. To replace a specific character in the CAMERA ID 1. Move the cursor to the editing area by pressing 2. Move the pointer to the character to be replaced by pressing €1 or Then move the cursor to the character area and select a new character. 3. Press [=□ to determine the CAMERA ID. To erase all characters in the editing area Move the cursor to RESET and press [I]. All characters in the editing area disappear. To determine the display position of the CAMERA ID 1. Move the cursor to POSI, and press CO. The display shown below appears and the CAMERA ID is highlighted. Highlighted 2. Move the CAMERA ID to the desired position by pressing 43 / [^/£®s. -2 3. Press E] to fix the position of the CAMERA ID. The mode returns to the previous CAMERA ID menu. Notes: • The CAMERA ID stops at the edges of the monitor screen. • The CAMERA ID moves faster if any of €3/ is kept pressed for a second or more. 2. Light Control Setting (ALC/ELC) You can select the mode for adjusting the lens iris. The modes are as follows: ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. ** CAM SET up ** CAMERA ID OFF ~1 ALC/ELC ALC: ~l SHUTTER OFF AGC ON (DNR-B) SENS UP OFF SYNC INT WHITE HAL ATW1. ~l MOTION DET OFF LENS DRIVE DC END SET UP ENABLE 2- 1. Move the cursor to the ALC/ELC parameter. 2. Select ALC or ELC. Cautions: 1. Under bright lighting conditions such as outdoors, use an ALC type lens because the ELC control range is not wide enough under these conditions. 2. Use an ALC type lens if the following phenomena occur: • Strong smear and/or blooming on highlight objects such as spotlight or sunlight from windows. • Noticeable flicker in the picture and/or color rendition variations. 3. If ELC is selected, SHUTTER is not available. Back Light Compensation (BACK LIGHT COMP) Back light compensation is available for both the ALC and ELC modes. It eliminates strong background lighting which makes the camera picture dark, such as a spotlight. You can select one of two modes {PRESET ON or PRESET OFF) of back light compensation. -2 2-1. ALC Mode with PRESET ON In normal use, the important object in a scene is placed in the center of the monitor’s screen. In the factory setup mode, m...