Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
To exit the menu screen Press the [MENU] button. To get back to the previous screen Press the cursor button left. . If you change the settings for [WIDE] (P43), [PICTURE SIZE] (P55) or [TV ASPECT] (P74), the screen size changes. (If you change [PICTURE SIZE] to or from [HDTV], the size changes.) VQT0X39 Setting date and time If the screen shows the incorrect date/time, then adjust it. ¬ Rotate the mode dial to select or . Press the menu button, then use the cursor button to select [ BASIC]# [ CLOCK SET]#[YES]. (P27) MENUSETUP ENTER EXIT SCENE MODE WIDE WIND CUT CLOCK SET BASIC NO YES REC MODE MENUEXIT CLOCK SET SET ENTER SETUP DEC 15 03 42 PM2006 Press the cursor button left or right to select the item (year/month/day/ hours/minutes) to be set. Then, press the cursor button up or down to set the desired value. . The year will change as follows: 2000, 2001, ..., 2099, 2000, ... . When [Y/M/D] or [D/M/Y] has been set for [DATE FORMAT], the 24-hour system is used to display the time. When [M/D/Y] has been set, the 12-hour system is used. Press the button in the center to enter the selection. . After pressing the menu button to finish the setting, check the date and time display. . The clock function starts at [00] seconds. Changing the display style MENUSETUP ENTER EXIT DISPLAY FORMAT CARD DATE/TIME QUICK START SETUP Y/M/D M/D/Y D/M/Y 1/3 DATE FORMAT Press the menu button, select [ SETUP]#[ DATE FORMAT], then use the cursor button to select the desired display style. (P27) Display style Screen display Y/M/D 15:42 2006.12.15 M/D/Y 3:42 PM DEC 15 2006 D/M/Y 15:42 15.12.2006 VQT0X39 Setting date and time (continued) Changing the date and time display style Press the menu button, select [ SETUP]#[ DATE/TIME], then use the cursor button to select the desired display style. (P27) . The date and time display can also be changed by pressing the [DATE/TIME] button on the remote control. [DATE] [D/T][OFF] MENUSETUP ENTER EXIT DISPLAY FORMAT CARD DATE/TIME QUICK START SETUP OFF D/T DATE 1/3 DATE FORMAT 3:42 PM DEC 15 2006DEC 15 2006 . About date/time . The date and time function are driven by a built-in lithium battery. . Make sure to check the time before recording because the built-in clock is not very accurate. . If [0] or [––] is indicated when this unit is turned on, then the built-in lithium battery runs down. After charging the battery using the steps below, set the clock. . Charging the built-in battery for the date . Connect the AC adaptor to this unit or place the battery on this unit, and the built-in lithium battery will be recharged. Leave this unit as is for approx. 24 hours, and the battery will save the date and time for approx. 6 months. (Even if the [ON/OFF] switch is set to [OFF], the battery is still being recharged.) Adjusting LCD monitor Adjusting the brightness and color level of the LCD monitor 1 Press the menu button, then use the cursor button to set [ SETUP]# [ LCD SET]#[YES]. (P27) MENUSETUP ENTER EXIT POWER SAVE LCD SET BEEP SOUND INITIAL SET SETUP YES NO 2/3 LCD AI LCD SET MENUSETUP ENTER SET EXIT Press the cursor button up or down to select the item to be adjusted. Then, press the cursor button left or right to make the adjustment. The bar display moves. – : Brightness of the LCD monitor – : Color level of the LCD monitor . These settings will not affect the images actually recorded. VQT0X39 Changing the picture quality on the LCD monitor (LCD AI) MENUSETUP ENTER EXIT POWER SAVE LCD SET BEEP SOUND INITIAL SET SETUP NORMAL DYNAMIC 2/3 LCD AI Press the menu button, then use the cursor button to select [ SETUP]# [ LCD AI]#[DYNAMIC] or [NORMAL]. (P27) – [DYNAMIC]: The image on the LCD monitor becomes clear and vivid. – [NORMAL]: Switches to the standard picture quality. . When [DYNAMIC] is set, the LCD . This function is automatically set to monitor is set to the color level and [DYNAMIC] when the brightness of the brightness optimally suited for the LCD monitor is increased (when [ ] is particular scenes to be recorded. Crisp displayed) and cannot be set to and bright images will be displayed. [NORMAL] independently. . The effect will vary depending on the . This will not affect the images to be scene recorded. recorded. In order to increase the brightness of the entire LCD monitor Press the [POWER LCD] button. [ ] appears on the LCD monitor. . If the [POWER LCD] button is pressed, the POWER LCD entire LCD monitor will become approx. twice as bright as the normal. . LCD stands for Liquid Crystal Display, and in this context refers to the LCD monitor. . When the button is pressed again, [ ] goes off, and the original brightness is restored to the LCD monitor. . This will not affect the images to be recorded. . When the AC adaptor is used, [ ] appears automatically and the monitor becomes brighter when the power is turned on. VQT0X39 Check before recording First, format the SD card if one which has been used on another device is going to be used for the first time on this unit. (P68) When the SD...