Évaluations - 3, GPA: 4.3
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Adjusting the Grip Belt Adjust the grip belt so that you can reach the grip zoom rocker with your index and middle fingers, and the START/STOP button with your thumb. IMPORTANT • Be careful not to drop the camcorder when adjusting the grip belt. Attaching a Shoulder Strap Pass the ends through the strap mount and adjust the length of the strap. IMPORTANT • Be careful not to drop the camcorder when attaching or adjusting the shoulder strap. Operating modes: [MLCD/VF Setup] [LCD/VF B&W] [Off] Preparing the Camcorder Removing and Attaching the Terminal Covers Remove the covers for the following terminals in order to access them. • HD/SD SDI and GENLOCK/TC terminals* • HD/SD COMPONENT OUT, USB and HDMI • W (headphone), AV and DC IN terminals OUT terminals • REMOTE terminal * b only. Removing the Terminal Covers 1 Open the terminal cover. 2 Grasp the strip connecting the terminal cover to the camcorder and pull straight out. Attaching the Terminal Covers Insert the connecting strip into the opening to attach the terminal cover. NOTES • If the connecting strip is difficult to grasp, use a pair of tweezers or similar tool. Using the Wireless Controller Inserting the Battery Insert the supplied CR2025 lithium button battery into the wireless controller before use. 1 Press the tab in the direction of the arrow () and pull out the battery holder (). 2 Place the lithium button battery with the + side facing up (). 3 Insert the battery holder (). Activating the Wireless Controller [JOther Functions] By default, the wireless controller is activated. If it has been deactivated, follow the procedure below to activate it. [Wireless Controller] Operating modes: [On] 1 Open the [Wireless Controller] submenu. [JOther Functions] [Wireless Controller] 2 Select [On] and then press SET. NOTES • You can also activate the wireless controller by setting an assignable button to [Wireless Controller] (097). Preparing the Camcorder Using the Wireless Controller to Operate the Camcorder When using the wireless controller, point it at the camcorder’s remote sensor. When the wireless controller's buttons are operated, the 34 camcorder's tally lamps will illuminate. NOTES • When you use the START/STOP button or ZOOM buttons on the wireless controller, you must press the record enable button simultaneously with the desired button. • When the camcorder cannot be operated with the wireless controller, or when it can only be operated at very close range, replace the battery. • The wireless controller may not work properly when the remote sensor is located under strong light sources or direct sunlight. Using a Tripod You can mount the camcorder on a tripod but do not use tripods with mounting screws longer than 5.5 mm (0.2 in.) as this may cause damage to the camcorder. Using a Tripod with 3/8" Mounting Screws To use a tripod with 3/8" mounting screws, first attach the optional TB-1 Tripod Adapter Base to the camcorder and then attach the tripod to the adapter base. 1 Remove the tripod base from the camcorder. • Remove the 4 screws and then remove the base. 2 Attach the optional TB-1 Tripod Adapter Base. • Firmly screw in the 4 screws. 3 Attach the tripod. • Firmly screw in the tripod screw. • If a tripod has both a 1/4" screw and 3/8" mounting screw, firmly screw in both. Preparing Recording Media Preparing Recording Media The camcorder records clips to CompactFlash (CF) cards and photos* to SD and SDHC memory cards. The camcorder is equipped with two CF card slots. Initialize recording media (037) when you use them with this camcorder for the first time. 35 * The camcorder can record custom picture settings (0101) and camera settings (0109) on to an SD card. To record a user memo (082) with a clip, use the supplied Canon XF Utility software to a create user memo file and save it to the SD card. The camcorder can read the file and embed it in the clip. Compatible CF cards You can use UDMA-compatible* Type I CF cards with a capacity of at least 512 MB with the camcorder. For more details on cards that can be used, visit your local Canon Web site. * The Ultra Direct Memory Access (UDMA) specification allows data to be transferred between the CF card and device at high transfer speeds (measured in MBps). Depending on the CF card, you may not be able to record even when using a UDMAcomptaible CF card. NOTES • Proper operation cannot be guaranteed for all CF cards. Inserting a CF Card You can insert a CF card into CF card slot A or slot B. If you have two CF cards, you can use both slots. 1 Slide the CF card slot cover switch in the direction of the E/A mark (). • The CF card slot cover will open to the left (slot A) or to the right (slot B). 2 Insert the CF card straight, with the label facing away from the lens, all the way into the slot until it clicks (). 3 Close the CF card slot cover. • Do not force the cover closed if the CF card is not correctly inserted. Preparing Recording Media 36 Checking the Status of the CF Card Slots You can che...
Ce manuel est également adapté pour les modèles :Caméscopes - XF100 (12.61 mb)