Évaluations - 1, GPA: 3
(
)
)
|
Photos et spécifications Canon XH G1S |
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
The device must comply with the IEEE1394 AV/C protocol. Use the optional CV-250F (4 pin-6 pin) DV cable or a commercially available 6 pin-6 pin DV cable to connect the external device. 1. Open the menu and select [SYSTEM SETUP/ ]. Select [DV CONTROL], set it to [ON ] and close the menu. MENU( 27) SYSTEM SETUP/ DV CONTROL•••OFF 2. Press the START/STOP button. If the button was pressed while the camcorder was in record pause mode: Camcorder and external device: start recording. If the button was pressed while the camcorder was recording: Camcorder and external device: stop recording (record pause mode). If the button was pressed while the camcorder was not ready to start recording: Camcorder: no change; External device: starts/stops recording following the camcorder’s control. If you press the START/STOP button again after solving the problem on the camcorder (inserting a cassette, etc.), the camcorder will start recording as the external device continues recording. • While both this camcorder and a connected device are recording, if this camcorder stops recording because of a condition other than pressing the START/STOP button (e.g., if the tape has reached its end), the connected device will continue recording. • When this camcorder stops recording you may notice a brief interruption of the audio on the connected device. • The status of the connected device is indicated as follows. Connected device is recording Connected device is in record pause or stop mode – – – Connected device is in a mode other than record pause or stop [DV CONTROL] is set to [ON ], but no external device is connected • As long as the built-in rechargeable lithium battery is charged, the camcorder retains the DV control setting even if you turn the power off. Make sure to check the setting after using the DV control function, as the tape in the connected device may be overwritten. • When connecting two DV Control-compatible Canon camcorders with a DV cable, make sure to set [DV CONTROL] on the other connected camcorder to [OFF]. • Up to 2 other devices can be connected to this camcorder for DV control. • With some non-Canon devices the DV control may not work properly depending on the connected device. External Connections 85 Recording an External Video Signal (HDV/DV In, Analog Line-In) You can record on the tape an external video signal, either from the HDV/DV input (SD or HD standard) or from the analog video input (SD standard). HDV/DV In When recording from an external digital device you can select the time code to be used for the recording made with this camcorder. Select [COPY] to keep the original time code of the video source, or [REGEN.] to use instead this camcorder’s internal time code. 1. Open the menu, select [SIGNAL SETUP] and then select the [TIME CODE] submenu. 2. Select [HDV/DV IN], select a setting option and close the menu. 3. Connect the camcorder to the external video device. 3 For the connection diagram to a digital device refer to Section of Connecting to a Monitor/TV ( 81). 4. Press the and buttons (or the REC PAUSE button on the wireless controller). • The camcorder enters the record pause mode. In this mode you can monitor the picture on the screen. • If you press only the button, recording will start immediately. 5. Press the button (or the PAUSE button on the wireless controller) when the scene you wish to record appears. Recording starts. 6. Press the button to stop recording. Analog Line-In 1. Open the menu and select [AUDIO SETUP]. Select [DV AUDIO], select a setting option and close the menu. 2. Connect the camcorder to the output terminals of the analog video device. 4 For the connection diagram to an analog device refer to Section of Connecting to a Monitor/TV ( 81). 3. Press the and buttons (or the REC PAUSE button on the wireless controller). • The camcorder enters the record pause mode. In this mode you can monitor the picture on the screen. • If you press only the button, recording will start immediately. 4. Press the button (or the PAUSE button on the wireless controller) when the scene you wish to record appears. Recording starts. 5. Press the button to stop recording. Copyright Signal Certain software tapes are copyright protected. If you attempt to play back such tape, “COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able to view the contents of the tape. If you attempt to record from such tape via the DV terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not be able to record the contents of the tape. We recommend powering the camcorder from a household power outlet. Converting Analog Signals into Digital Signals (Analog-Digital Converter) Using the camcorder you can convert analog video input signals to a digital video signal (SD standard) and output it through the HDV/DV terminal. MENU SIGNAL SETUP AV DV••••••••OFF ( 27) Open the menu and select [SIGNAL SETUP]. Select [AV DV], set it to [ON] and close the menu. • Depending on the signal sent fro...
Ce manuel est également adapté pour les modèles :Caméscopes - XH A1S (7.35 mb)