Log:
Évaluations - 3, GPA: 2 ( )

Instructions Canon, Modèle MVX250i

Fabricant : Canon
Taille : 8.19 mb
Nom Fichier :
Langue d'enseignement: en
Photos et spécifications   Canon  MVX250i
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust to temperature changes slowly before removing it from the bag. When condensation is detected: . The camcorder stops operating and the warning message “CONDENSATION HAS BEEN DETECTED” appears for approx. 4 seconds and h starts flashing. . If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and v starts flashing. Remove the cassette immediately and leave the cassette compartment open. Leaving the cassette in the camcorder may damage the tape. . A cassette cannot be loaded when condensation is detected. Resuming use: . It takes about 1 hour until the water droplets evaporate. After the condensation warning stops flashing, wait for 1 more hour before resuming use. E Battery Pack Handling Precautions DANGER! Treat the battery pack with care. • Keep it away from fire (or it might explode). • Do not expose the battery pack to temperature higher than 60 .C. Do not leave it near a heater or inside a car in hot weather. • Do not try to disassemble or modify it. • Do not drop or knock it. • Do not get it wet. . Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day before, to ensure a full charge. . Attach the terminal cover whenever a battery pack is not in use. Contact to metallic objects may cause a short circuit and damage the battery pack. . Dirty terminals may cause a poor contact between the battery pack and the camcorder. Wipe the terminals with a soft cloth. . Since storing a charged battery pack for a long time (about 1 year) can shorten its lifecycle or affect performance, we recommend to discharge the battery pack fully and to store it in a dry place at temperatures no higher than 30 °C. If you do not use the battery pack for long periods, charge and discharge it fully at least once a year. If you have more than 1 battery pack, perform these precautions at the same time for all battery packs. . Although the battery pack’s operating temperature range is from 0 °C to 40 °C, the optimal range is from 10 °C to 30 °C. At cold temperatures, performance will temporarily decline. Warm it in your pocket before use. . Replace the battery pack if the usable time after full charge diminishes substantially at normal temperatures. About the battery terminal cover The battery terminal cover has a [ ]-shaped hole. This is useful when you wish to differentiate between charged and uncharged battery packs. For example, with charged battery packs, attach the terminal cover so that the [ ]-shaped hole shows the blue label. Back side of the Terminal cover attached AdditionalInformation battery pack Charged Uncharged 145 Cassette Handling Precautions . Rewind tapes after use. If the tape becomes slack and damaged, it may cause picture and sound distortion. . Return cassettes in the case and store them upright. . Do not leave the cassette in the camcorder after use. . Do not use spliced tapes or nonstandard cassettes as they may damage the camcorder. . Do not use tapes that have been jammed as video heads may become dirty. . Do not insert anything into the small holes of the cassette, or cover them with cellophane tape. . Handle cassettes with care. Do not drop or subject them to severe impact as this may damage the cassettes. . Rewind tapes from time to time if they are stored for a long time. . With cassettes equipped with a memory function, metal plated terminals may become dirty with use. Clean the terminals with a cotton swab after about 10 times of loading/unloading. The memory function is not supported by the camcorder. Protecting Tapes from Accidental Erasure To protect your recordings from accidental erasure, slide the tab on the cassette to the left. (This switch position is usually labelled SAVE or ERASE OFF.) If you load a protected cassette in CAMERA mode, the message “THE TAPE IS SET FOR ERASURE PREVENTION” appears for approx. 4 seconds and v starts flashing. If you wish to record on that cassette, slide the tab back to the right. Memory Card Handling Precautions . Format new memory cards with the camcorder. Memory cards formatted with other devices such as a computer may not operate correctly. . We recommend saving backups of memory card images on your computer’s hard drive or other external memory device. Image data may be corrupted or lost due to memory card defects or exposure to static electricity. Canon Inc. makes no warranties for corrupted or lost data. . Do not turn off the camcorder, disconnect the power source, open the memory card cover or remove the memory card while the card access indicator is flashing. . Do not use memory cards in places subject to strong magnetic fields. . Do not leave memory cards in places subject to high humidity and high temperature. . Do not disassemble memory cards. . Do not bend, drop, or subject memory cards to shocks and do not expose them to water. SAVE REC SAVE REC E . Moving a memory card rapidly between hot and...

Ce manuel est également adapté pour les modèles :
Caméscopes - MVX200i (8.19 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories