Évaluations - 1, GPA: 4
(
)
)
|
Photos et spécifications Canon Digital IXUS 75 |
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Battery charge is low. Recharge it as soon as possible if it will be used for an extended period. Change the battery pack Battery charge is insufficient to operate the camera. Replace the battery immediately. Fig. A Fig. B You may be able to check the charge state depending upon how the terminal cover is attached (Fig. C, D). • You are recommended to use it in the camera until it is completely discharged and to store it in an indoor location with low relative humidity and between the temperatures of0 – 30 °C (32 – 86 °F). Storing a fully charged battery for long periods of time (about one year) may shorten its life cycle or affect its performance. If you do not use the battery for long periods of time, charge it fully and discharge it fully in the camera about once a year before returning it to storage. Fig. C Fig. D Charged BatteryAttach it so the is visible Spent BatteryAttach it the opposite way to Fig. C. Charging the Battery • Since this is a lithium-ion battery, you need not completely discharge it before recharging. • It takes approximately 1 hour 30 minutes to fully charge the battery from a depleted state (based on Canon’s testing standards). • Charging it within a temperature range of 5 – 40 °C (41 – 104 °F) is recommended. • Charge times may vary according to the ambient temperature and the battery's charge state. • You are advised to charge the battery on the day of use, orone day before, to ensure a full charge. Even charged batteries continue to discharge naturally. • If the performance of the battery diminishes substantially even when it is fully charged, its life has been exceeded andit should be replaced. Appendix 127 Handling the Memory Card Handling the Memory Card SD Memory Card and SDHC Memory Card Write Protect Tab Slide the switch up. Slide the switch down (you can protect the images and other data on the card) Write Protect Tab Writing/Erasing Possible Writing/Erasing Impossible Cautions When Handling • Memory cards are high-precision electronic devices. Do not bend them, apply force to them, or subject them to shocks or vibration. • Do not attempt to disassemble or alter the memory card. • Do not allow dirt, water or foreign objects to contact the terminals on the back of the card. Do not touch the terminals with your hands or metal objects. • Do not peel away the original label on the memory card orcover it with another label or sticker. • When writing on the memory card, do not use a pencil orball-point pen. Only use a soft point pen (e.g. felt-tip pen). .. Do not use or store memory cards in the followinglocations. • Locations subject to dust or sand • Locations subject to high humidity and high temperatures • Since some or all of the data recorded on the memory card may be corrupted or erased by electrical noise, static electricity, or camera or card malfunction, making a backupcopy of important data is recommended. Formatting • Please note that formatting (initializing) an memory carderases all data, including protected images. • You are recommended to use memory cards that have been formatted in your camera. • The card supplied with the camera may be used without further formatting. • When the camera is malfunctioning, a corrupted memory card might be the cause. Reformatting the memory card may solve the problem. • When a non-Canon brand memory card is malfunctioning, reformatting it may solve the problem. • Memory cards formatted in other cameras, computers, or peripheral devices may not operate correctly in this camera. When that happens, reformat the memory card with this camera. • If formatting in the camera does not work properly, turn the camera off and re-insert the memory card. Then turn the camera back on and format again. • Data on a card is not completely erased even when the cardis formatted or images are erased because these processesmerely change the file management data. Please note this fact when transferring ownership or disposing of cards. Take care to destroy the card when disposing of it to prevent the leakage of personal data. Appendix 129 Using an AC Adapter Kit (Sold Separately) Using an AC Adapter Kit (Sold Separately) It is best to power the camera with AC Adapter Kit ACK-DC10 (sold separately) when you are using it for long periods of time or connecting it to a computer. Turn the camera power off before connecting or disconnecting the AC adapter. 1 Connect the power cord to the compact power adapter first and then plug the other end into the power outlet. 2 Open the memory cardslot/battery cover, push the battery lock in the direction of the arrow and insert the DC coupler until it locks. ..Slide the memory card slot/battery cover closed. 3 Open the DC coupler termi- nal cover and attach the cord to the DC terminal. Compact Power Adapter CA-DC10 Battery Lock DC Coupler DR-10 Using an Externally Mounted Flash (Sold Separately) Using an Externally Mounted Flash (Sold Separately) High-Power Flash HF-DC1 This flash is used to supplement the camera's built...
Ce manuel est également adapté pour les modèles :Caméscopes - Digital IXUS 70 (6.72 mb)