Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
• If your antenna system has both a coaxial lead and twin 300-ohm leads, purchase a combiner (available at electronics stores). Press or screw the coaxial lead onto the combiner; place the twin leads underneath the screws on the combiner and tighten the screws. Press the cable from the combiner onto the ANT. IN terminal on the back of your VCR. VCR ANT.IN VCR ANT.IN 7 Daewoo Video Cassette Recorder User’s Guide Overview of the equipment,continued Accessories Carefully remove the VCR from the carton. Check that the VCR has not been damaged. The following accessories are included. 1 Wireless Remote Control NOTE : Required 2 ‘AAA’ batteries. 2 Coaxial cable for connecting the VCR to your TV’s VHF terminal. To get a replacement remote, please call1-800-DAEWOO8(1-800-323-9668) to get a replacement remote and talk to parts department. 9 Daewoo Video Cassette Recorder User’s Guide Daewoo Video Cassette Recorder User’s Guide 10 Connecting your VCR,continued • If you have a coaxial terminal for VHF signals and twin lead terminals for UHF signals, you need an adapter(Not supplied) as shown below: • If you have twin lead terminals for all signals, you need an adapter(Not supplied) like this: If your TV does not have Audio/Video inputs, you have finished connecting your VCR to your TV. If your TV does have Audio/Video inputs, you may want to follow the section below. Connecting to a TV with Audio/Video inputs 1 Connect a video cable to the VIDEO OUT terminal on the back of the VCR. 2 Connect the other end of the video cable to the VIDEO IN terminal on the TV. . TV . TV TV . Connecting your VCR,continued • If your antenna system has two sets of twin 300-ohm leads, purchase a combiner (available at electronics stores). Place one set of twin leads underneath the screws on the combiner and tighten the screws. Do the same with the other set of twin leads. Press the cable from the combiner onto the ANT. IN terminal on the back of your VCR. Connecting your VCR to your TV 1 Connect one end of a coaxial cable to the RF OUT terminal on the back of the VCR. 2 Connect the other end of the coaxial cable to the ANT. IN terminal on the back of the TV. ANT.IN VCR ANT.IN VCR . TV 11 Daewoo Video Cassette Recorder User’s Guide Daewoo Video Cassette Recorder User’s Guide 12 • If your cable system requires you to use a converter box for all channels, connect the incoming cable to the IN terminal on the converter box. Connect another cable between the OUT terminal on the converter box and the ANT. IN terminal on the VCR. Keep your VCR tuned to channel 3 or 4 and change channels using the converter box. • If your cable system only requires you to use a converter box for some channels (i.e., pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this cable into a splitter (available at your local electronics store.) Connect one coaxial cable between one OUT terminal on the splitter and the IN terminal on the converter box. Connect another coaxial cable between the other OUT terminal on the splitter and the A-IN terminal on an A/B switch (available at your local electronics store.) Connect a third coaxial cable between the OUT terminal on the converter box and the B-IN terminal on the A/B switch. Connect a coaxial cable between the OUT terminal on the A/B switch and the ANT. IN on your VCR. When the A/B switch is in the B position, use the converter box to change channels ; when the A/B switch is in the A position, use the VCR to change channels. VCR ANT.IN VCR Connecting your VCR,continued 3 Connect a pair of audio cables to the AUDIO OUT terminal on the back of the VCR. If you have a mono (non-stereo) TV, connect only the white (left) terminal. 4 Connect the other end of the audio cables to the AUDIO IN terminals on the TV. If you have a mono (non-stereo) TV, connect only the white (left) terminal. Connecting a cable system If your cable set-up is not described below, please contact your cable company for more information. • If your cable system does not require the use of a cable box, simply press or screw the incoming cable onto the ANT IN terminal on the back of your VCR. VCR ANT.IN Connecting your VCR,continued Seting up your remOontec ec oyonutr ohla, vyeo cuo anrnee rceteadd however , you must be certain to do the folowing: • Turn on the television. • Tune the television to channel 3 or 4 (whichever channel you selected when connecting the Turning the VCR on 1 Press POWER on the remote control. You can also press POWER on the VCR’s front panel. 2 Set the VCR to VCR mode by pressing TV/VCR on the remote control if the VCR indicator “VCR” is not lit. Changing the on-screen menu language You may select the language in which you would like the VCR’s menu to be displayed: English, Spanish, or French. 1 Press MENU to display the main menu. 2 Press 5 to select Language. 3 4 Press 1 to select English, 2 to select Espanol or 3 to select Francais. Press MENU once to return the main menu, which will be displayed in t...