Log:
Évaluations - 4, GPA: 4.3 ( )

Instructions Sony, Modèle SLV-SE800N

Fabricant : Sony
Taille : 1.16 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


Check your model number by looking at the rear panel of your VCR. SLV-SE800N is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE500K only.” Unpacking Step 2 : Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Using the remote commander You can use this remote Remote sensor commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV. 1 2 3 4 5 6 7 8 0 [TV] / [VIDEO] To operate Set [TV] / [VIDEO] to the VCR [VIDEO] and point at the remote sensor at the VCR a Sony TV [TV] and point at the remote sensor at the TV Getting Started continued 5 Setting up the remote commander WIDEAUDIO MONITOR FASTEXT buttons DISPLAY –/– – TV control buttons 1 2 3 4 5 6 7 8 0 ? ????/1 1111 / //// a aaaa t tttt TV/VIDEO Programme number buttons PROG +/–/ c cccc/C CCCC 2 2222 +/– To Press Set the TV to standby mode ?/1 Select an input source: aerial in or line in t TV/VIDEO Select the TV’s programme position Programme number buttons, –/– –, PROG +/– Setting up the remote commander To Press Adjust the volume of the TV 2 +/– Switch to TV (Teletext off)* a (TV) Switch to Teletext* / (Teletext) Select the sound AUDIO MONITOR Use FASTEXT* FASTEXT buttons Call up the on-screen display DISPLAY Change the Teletext page* c/C Switch to/from wide mode of a Sony wide TV (For other manufactures’ wide TVs, see “Controlling other TVs with the remote commander (not available on SLV- SE350K and SE600N)” below.) WIDE Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery together with an old one. • Do not use different types of batteries together. • Some buttons may not work with certain Sony TVs. * not available on SLV-SE350K and SE600N Controlling other TVs with the remote commander (not available on SLV-SE350K and SE600N) The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number. 1 Set [TV] / [VIDEO] at the top of the remote commander to [TV]. 2 Hold down ?/1, and enter your TV’s code number using the programme number buttons. Then release ?/1. Now you can use the following TV control buttons to control your TV: ?/1, t TV/VIDEO, programme number buttons, –/– – (ten’s digit), PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*, M/m/ Ce manuel est également adapté pour les modèles :
joueurs de magnétoscope / vidéo - SLV-SE350K (1.16 mb)
joueurs de magnétoscope / vidéo - SLV-SE500K (1.16 mb)
joueurs de magnétoscope / vidéo - SLV-SE600N (1.16 mb)
joueurs de magnétoscope / vidéo - SLV-SE700N (1.16 mb)


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories