Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
When the battery weakens, the LED on the remote will dim and operating range will be reduced. © 2006 Directed Electronics—all rights reserved FCC/ID Notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Caution This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use. © 2006 Directed Electronics—all rights reserved Transmitter Functions The receiver uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any specific transmitter button, or combination of buttons, to any receiver function. The transmitter initially comes programmed with the Standard Configuration, but may also be customized by an authorized dealer. Unless otherwise specified, the buttons used in all of the instructions in this manual correspond to a Standard Configuration transmitter. Standard Configuration Button The door locking and unlocking functions are controlled by pressing . Button The channel 2 output or trunk release is controlled by the button. Button The remote engine start function of your system is controlled by pressing . Button (OPT) No function with this system © 2006 Directed Electronics—all rights reserved Buttons + When simultaneously pressed these buttons control the timer mode. Buttons + When simultaneously pressed these buttons control the turbo/short run mode. Buttons + + When simultaneously pressed these buttons control the rear window defogger during remote engine starting. Using Your System Warning! Safety First The following safety warnings must be observed at all times: ¦ Due to the complexity of this system, installation of this product must only be performed by an authorized Ungo Dealer. ¦ When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote engine © 2006 Directed Electronics—all rights reserved start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote engine start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility of the user. ¦ Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Ungo dealer in accordance with the Safety Check outlined in the product installation guide. If the vehicle starts in gear, cease remote engine start operation immediately and consult with the authorized Ungo dealer to fix the problem. ¦ After the remote engine start module has been installed, contact your authorized dealer to have him or her test the remote engine start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when © 2006 Directed Electronics—all rights reserved performing the Neutral Safety Shutdown Circuit test, the remote engine start unit has not been properly installed. The remote engine start module must be removed or the installer must properly reinstall the remote engine start system so that the vehicle does not start in gear. All installations must be performed by an authorized Ungo dealer. OPERATION OF THE remote engine start MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE remote engine start SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED UNGO DEALER TO REPAIR OR DISCONNECT THE INSTALLED remote engine start MODULE. UNGO WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Locking Pressing for one second...