Log:
Évaluations - 5, GPA: 4.2 ( )

Instructions Audiovox, Modèle PRO-9342FT3

Fabricant : Audiovox
Taille : 212.85 kb
Nom Fichier : 85946bb2-8e4f-4200-b06e-59d9ce250141.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


RF Programmable Features : Feature Selection 1 Chirp 1st Door L/UL 1 Sec. 2nd Accy Lock Auto Lock On 3rd Accy. UL Auto UL Dr. 4th Passive Locks Passive 5th Passive/Active Arm Passive Arm 6th Voltage Sense Voltage Sense 7th Siren/Horn Siren/Horn 8th Horn Chirp 10mS 9th Override Method Custom Code 10th Chirp Delete From Tx On 2 Chirps 3.5 Sec. Auto Lock Off Auto UL All Active Active Arm Hardwire Siren Only 16mS Valet Off To program these selectable features; Action Turn ignition on Press and release the valet switch 3 times Within 3 seconds, turn ignition Off First Then On Press transmitter Lock button to change Press transmitter Lock button to change or Second Press and release the valet switch Press transmitter Lock button to change or Third Press and release the valet switch Press transmitter Lock button to change Press transmitter Lock button to change or Fourth Press and release the valet switch Press transmitter Lock button to change or Fifth Press and release the valet switch Press transmitter Lock button to change or 3 Chirps 4 Chirps Default 1 Sec L, Dbl. U/L 1 Sec. Auto Lock Off Auto UL Off Auto UL Off Active Active Arm Hardwire Horn Only Siren/Horn 30mS 16mS Valet Off System Response No response 1 Chirp - LED 1 flash Short chirp, then long chirp 1 chirp = 1 second door locks 2 chirps = 3.5 second door locks 3 chirps = 1 sec. lock, dbl 1 sec. unlock 2 chirps = auto locks off 1 chirp = auto locks on 3 chirps = auto unlock off 1 chirp = auto unlock drivers door only 2 chirps = auto unlock all doors 2 chirps = active locks 1 chirp = passive locks 2 chirps = active arming 1 chirp = passive arming Sixth Press and release the valet switch 2 chirps = hardwire Press transmitter Lock button to change 1 chirp = voltage sense or Seventh Press and release the valet switch 1 chirp = siren and horn output Press transmitter Lock button to change 2 chirps = siren output only Press transmitter lock button to change 3 chirps = horn output only or Eighth Press and release the valet switch 2 chirps = horn chirp output 16mS Press transmitter Lock button to change 3 chirps = horn chirp output 30mS Press transmitter Lock button to change 1 chirp = horn chirp output 10 mS or Ninth Press and release the valet switch 2 chirps = valet switch override operation Press transmitter Lock button to change 1 chirp = custom code override operation or Tenth Press and release the valet switch 2 chirps = chirp delete from transmitter inactive Press transmitter Lock button to change 1 chirp = chirp delete from transmitter active Press and release the valet switch Exit program mode or Turn ignition key off Exit program mode Note: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the programming will be terminated. INSTALLATION OF MAJOR COMPONENTS Control Module: Select a mounting location inside the passenger compartment ( up behind the dash ), and secure using the two screws provided. The control module can also be secured in place using cable ties. Do not mount the control module in the engine compartment, as it is not waterproof. You should also avoid mounting the unit directly onto factory installed electronic components. These components may cause RF interference, which can result in poor transmitter range or intermittent operation. Siren: Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas near high heat components or moving parts within the engine compartment. To prevent water retention, the flared end of the siren must be pointed downward when mounted. Mount the siren to the selected location using the screws and bracket provided. Hood or Trunk Pin Switch: A pin switch is included for use in protecting the hood or trunk ( or hatchback ) of the vehicle. The switch must always be mounted to a grounded, metal surface of the vehicle. It is important to select a location where water cannot flow or collect and to avoid all drip gutters on hood and trunk fender walls. Choose locations that are protected by rubber gaskets when the hood or trunk lid is closed. The pin switch can be mounted using the bracket provided, or direct mounted by drilling a . " diameter mounting hole. Keep in mind that when properly mounted, the plunger of the pin switch should depress at least . " when the hood or trunk lid is closed. Page 2 Dash Mounted LED: A small red LED is included that will serve as a visual indicator of the alarm status. It should be installed in the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver. Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill will not damage any existing components as it passes through the panel. Drill a . " diameter hole, and pass the red and blue wires from the LED through the hole, from the front of the panel. Firmly press the body of the LED into the hole until fully seated. Valet Sw...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories