Évaluations - 4, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Use this command to silence your Command Center sounder during service alert, and to reset the Command Center alarm memory. COMMAND To use COMMAND 4: 1. Ensure that your security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the [_4j key. The Command Center sounder is silenced, and any flashing Zone Status indicator lights are turned off if the zone is normal. 13 Transmit Test Report O I have this feature. □ I do not have this feature. Testing the communication link between your security system and the Central Station is an important part of maintaining a high level of security for your property. The Command Center minimizes the time and trouble of testing by allowing you to send a special test signal by pressing three keys. Arming the system is not necessary, however you should always call the Central Station before transmitting a test report. COMMAND 4 ¡11 To use COMMAND 4 1: 1. Ensure that your security system is disarmed. 2. Press the I COMMAND 1 bar. The Command Mode indicator light comes on. 3. Press the ¡¡§| key, and then press the jig key. 4. After the report is received at the Central Station, the Command Center will emit a beep tone for two seconds. This is to confirm that the test signal was properly transmitted and received. 14 COMMAND 4 3 Enable Remote Account Management |i COMMAND O I have this feature. O I do not have this feature. 2. Call the Central Station using this phone number: Your security system has the ability to be managed remotely from the Central Station without having a serviceperson on the protected premises. By using COMMAND 4 3, you can enable remote account management from the Central Station. Remote account management is done with the aid of a specially equipped computer at the Central Station. Typical remote programming changes may include: adding or deleting system commands, and changing personal passcodes or entry/exit delay times. To use COMMAND 4 3: 1. Ensure that your security system is disarmed. 3. This number is designated for the Remote Account Manager. You must make the call using the telephone located: Identify yourself and your premises (account number, name, address, etc.) and advise the operator of the programming changes you wish to have performed. 4. When the operator directs you, enter COMMAND 4 3 at your Command Center: Press the I COMMAND j bar. The Command Mode 5. 6. indicator light comes on. Press the §§§ key, and then press the ¡¡|j key. The telephone line that the call was made from is not active when remote account management is in progress. You may hang up the telephone. When remote account management has been completed, your telephone line is restored to normal service. 15 Local System Test O I have this feature. □ I do not have this feature. It is easy for you to test your security system without sending reports to the Central Station. The local system test is performed only when the security system is disarmed. To ensure that your security system is operating properly, and should be used to test your system regularly. COMMAND 4 4 is used to test your security system. This command tests your Command Center, system's sounders (both interior and exterior) and the system's detection devices. No alarm reports are sent to the Central Station unless a 24-hour zone is faulted (e.g.: panic, fire, duress). (Cohtact your Central Station before you test your fire protection system because an alarm report may be transmitted.) To test individual detection devices, simply activate sensors, and open protected doors and windows‘one at a time. As detection devices are faulted, the Command Center display panel indicates the faulted zone. This verifies that the detection device is working properly. COMMAND 4 4 To use Local System Test: 1. Ensure that your security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the ||j|j key twice. Audible devices (both interior and exterior) sound. To silence the audible warning, press any numeric key on the Command Center keypad. 4. After silencing the audible devices, you may test detection devices. Open a door or window, or activate a motion sensor. The Command Center display panel indicates the zone which you have faulted. This verifies that the detection device is working properly. 5. To end the Local System Test, press any numeric key on the Command Center. 16 Reset Detectors C\ I have this feature. O I do not have this feature. Using this COMMAND 4 7, you are able to reset faulted detection devices from your Command Center. Devices may include smoke detectors, shock sensors or a variety of other detection devices. Ask your alarm technician which zones you can reset from the Command Center by entering COMMAND 4 7. When this command is used, the Command Center is also "reset." During this time, the Command Center is momentarily deactivated, and cannot perform any ...
Ce manuel est également adapté pour les modèles :Vidéo - Security System 4112 (1.38 mb)