Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
For example, if you wanted to secure Door 5, at the following prompt: SECURE DOOR 1 2 3 4 5 6 7 8 Press 5 then ENT. The display will read: SECURE DOOR 1 2 3 4 X 6 7 8 This indicates that all doors are at a normal state, except for Door 5, which is secured. 16. Press ESC to leave this subfunction, or enter another door number to unlock. NOTE: Each of these subfunctions act as a toggle. To return a door to its normal state, follow the same procedure you used to change its state. For example, if Door 3 is secured and you wish to return it to its normal state, at the SECURE DOOR? prompt, enter 3 and press ENT. The door will no longer be secured and the X will be replaced with the number 3. D9412/D7412 Owner’s Manual Supplement 33267D 12/97 Page 6 DELETE USER? COMMAND 53 Description Use this function to delete a personal passcode from your system without assistance from your security company. You need to know the user number for the passcode you want to delete.. I have this feature. I do not have this feature. Using DEL USER ? 1. Ensure the display shows idle disarmed text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press 5 and 3. NOTE: If you prefer, you may use the Function List in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Function List, then press NEXT repeatedly until you reach the DEL USER? prompt. Press ENT. 4. The display shows DEL USER #. Key in the user number and press ENT. If you do not know the user number, press the NEXT key (go to step 6). 5. USER ## (or user text, such as the name of the user, if this feature was programmed into your system by your security company) will be displayed allowing for confirmation. Press ENT. If this is not the user you wish to delete, press the NEXT or PREV key until the correct user name appears, then press the ENT key. 6. The display will now read DELETE USER ##? Press ENT if you wish to have this user deleted, and USER DELETED will be displayed. If the user number is not in the system, NOT IN USE will be displayed. If you made an error and do not wish to delete this user, press ESC. D9412/D7412 Owner’s Manual Supplement Page 7 33267D 12/97 ADD/CHNG USER? COMMAND 56 Description Use this function to add or change a passcode/card without assistance from your security company. Before adding or changing a passcode/card, you will need to know which user numbers are available, the authority level you want to assign to the new user, and the areas in which the passcode/card will be valid. I have this feature. I do not have this feature. Using Add User ?: 1. Ensure the display shows idle disarmed text. 2. Press the COMMAND bar. The display shows SYSTEM COMMAND. 3. Press 5 and 6. NOTE: You may also use the Function List in place of steps 2 and 3 to initiate this function. Press the MENU key to enter the Function List, then press NEXT until you reach the ADD/CHNG USER? prompt. Press ENT. 4. The display shows ENTER USER #. Key in the user number and press ENT. 5. The display shows USER # (or user text, such as the name of the user, if this feature was programmed into your system by your security company) to allow for confirmation. Press ENT if the correct user number (or user name) is displayed. Press ESC if not. 6. ADD PASSCODE? is displayed (If the user number already exists, CHANGE PASSCODE? is displayed). Press ENT. ENTER NEW CODE is displayed. Enter the new passcode followed by ENT. ENTER AGAIN is displayed. Enter the new passcode a second time for confirmation. Press ENT. The display will read PASSCODE ADDED (or PASSCODE CHANGED if the user number was already in the system). NOTE: The system will not accept a passcode that is within two digits of an existing passcode. This is to avoid conflicts with duress passcodes. For example, if passcode 123 is already programmed in the system, the system will not accept 121, 122, 124, or 125 as passcodes. On Systems With Access Control... 7. If your system includes access control features, such as card readers at doors, etc., the following prompt will be displayed: ADD CARD? (CHANGE CARD? will be displayed for users who already have cards.) 8. If the user is to have card/token access to the building or area press ENT. PRESENT CARD will be displayed. Present the card at the card reader and wait for the tone. If the card/token is read correctly, a tone will sound and the command center will display CARD ADDED (or CARD CHANGED if the user already had a card/token). Press ENT. 9. ADD LEVEL? (CHANGE LEVEL? If the user number already exists) is displayed. Press ENT. 10. VALID AREA 1? is displayed. If you wish this user number to be valid in Area 1, press ENT. If not, press NEXT. 11. AUTH LEVEL is displayed. Assign the authority level you wish the user number to have for this area and press the ENT key. Be sure to record this information. 12. VALID AREA 2? is displayed. Enter the information as necessary for the areas in the scope of the command center by following steps 10 and 11 ...
Ce manuel est également adapté pour les modèles :Vidéo - Security System D7412 (33.42 kb)