Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
(FINE adjustment can be made up to 22.5 degrees by pressing or .) Notes: • When the T cursor reaches the “+” end, it jumps back to At the same time, COARSE is incremented by one step to enable a continuous adjustment. The reverse takes place when the "I" cursor reaches the end. • When d or is kept pressed for a second or longer, the “I" cursor moves faster. 3- • To reset COARSE and FINE to the values preset at the factory, press 6 or 0 simultaneously. COARSE and FINE adjustments are preset at the factory to zero-crossing of the AC line phase. • If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of the camera video output signal may be disturbed. 7. White Balance Setting (WHITE BAL) 7-1. Auto-Tracing White Balance Mode (ATW) You can select one of two modes for white balance adjustment as follows: • ATW (Auto Tracing White Balance) In this mode, the color temperature is monitored continuously and thereby white balance is set automatically. The color temperature range for the proper white balance is approximately 2 600 - 6 OOOK. Proper white balance may not be obtained under the following conditions: 1. The color temperature is out of the 2 600 -6 OOOK range. 2. When the scene contains mostly high color temperature objects, such as a blue sky or sunset. 3. When the scene is dim. In these cases, select the AWC mode. Move the cursor to the WHITE BAL parameter and select ATW. The white balance of the camera is automatically set. ** CAM SET OP * * CAMERA ZD OFF “I ALC/ELC ALC “I SHOTTER --- AGC ON SENS OP OFF SYNC ZNT WHITE BAL !ATW MOTZON DET OFF 1 LENS DRIVE DC RET V- Automatic White Balance Control Mode (AWC) In this mode, accurate white balance is obtained within a color temperature range of approximately 2 300-10000K. Move the cursor to the WHITE BAL parameter and select AWC -»PUSH SW. -- ** CAM SET OP ** CAMERA ID OFF 1 ALC/ELC ALC n SHUTTER --- AGC ON SENS OP OFF SYNC I NT WHITE BAL AWC-tPOSBiSW MOTION DET OFF 1 LENS DRIVE DC RET 2. Press El to start the white balance setup. The words PUSH SW start blinking to indicate that the white balance is being set. ** CAB SET UP *» CAMERA ID ALC/ELC SHUTTER AGC SENS DP SYNC WHITE BAL MOTION DET LENS DRIVE RET OPP ALC ON OFF INT AWC-»PDSHfsW OFF 1 DC / Blinking 3. When the white balance setting is completed, the words PUSH SW stop blinking. 4. When you want to adjust the white balance manually, press 13 to select AWC and press El ■ The AWC menu appears on the monitor. (When ATW is selected, pressing El displays the ATW menu.) (-^ ** CAM SET OP ** CAMERA ID OFF “1 ALC/ELC ALC 1 SHUTTER --- AQC ON SENS OP OFF SYTJC INT WHITE BAL Awe: ~1 MOTION DET OFF 1 LENS DRIVE DC RET -3 Fine Adjustment for AWC (ATW) Manually You can add the detailed setting for white balance setting manually. 1. To set MASK SET, proceed as described in steps 1 to 4 of "ALC mode with SUPER-D OFF and ELC mode” on page 26. 2. Move the cursor to R. 3. Press or to obtain the optimum amount of red gain. 4. Move the cursor to B. 5. Pressd or [3 to obtain the optimum amount of blue gain. Note: When you need to set MASK SET. re-adjust to obtain the optimum amount of red and blue gain. 5- 8. Motion Detector Setting (MOTION DET) The motion detector detects the moving objects in the scene by monitoring the brightness level changes. You can select the level of sensitivity for motion detection. Note: The alarm signal is supplied only when RS485 communication is used. 1. Move the cursor to the MOTION DET parameter and select ON. 2. Press El. The MOTION DETECT menu appears on the monitor screen. - ** CAM SET UP •• CAMERA ID 07T “1 AI«C/&LC ALC “1 SHUTTER --- AQC OH SENS OP OFF SYNC I NT WHITE BAL AWC “1 MOTION DET 1 LENS DRIVE DC -3 3. Move the cursor to MASK SET and press ©. The MASK SET menu has 48 masks. To set MASK SET, proceed as described in steps 2 to 4 of UALC mode with SUPER-D OFF and ELC mode" on page 26. 4. Move the cursor to the ALARM parameter and select ON or OFF to set the alarm in the DISPLAY MODE. Note: When the system controller WV-RM70, WV-CU550 or WV-CU550A is used with this model, select OFF for ALARM. 5. Move the cursor to DISPLAY MODE and press Q] to see the current setting. The masks that detect the brightness changes start blinking. 6. To raise detection sensitivity, press El to return to the MOTION DETECT menu. 7. To obtain the optimum detection level, move the T cursor to adjust the level. 8. Repeat the procedures above to obtain a satisfactory setting. 9. Move the cursor to RET and press OD to return to the CAM SET UP menu. Notes: • Masking or adjusting the detection level is needed to prevent malfunction under the following conditions: • When shooting an object under flickering fluorescent light or shooting in ELC. • When leaves or curtains etc. are swayed by the wind. • When the object is lighted by ligh...