Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Fasten the camera cable to this connector firmly. If not, noise may be appeared. Camera Head Side Pin No. Camera Control Unit Side -9V Input 1 -9V Output +5V Input 2 +5V Output +15V Input 3 + 15V Output G Signal Output 4 G Signal Input V2 Input 5 V2 Output R Signal Output 6 R Signal Input V4 Input 7 V4 Output +25V Input 8 +25V Output Vi Input 9 V1 Output V3 Input 10 V3 Output RGB Ground(GND) 11 RGB Ground(GND) SHT(R) Input 12 SHT(R) Output N. C. 13 N. C. B Signal Output 14 B Signal Input Ground(GND) 15 Ground(GND) N. C. 16 N. C. SHT(G) Input 17 SHT(G) Output SHT(B) Input 18 SHT(B) Output H2 Input 19 H2 Output RG Input 20 RG Output Caution : Connecting or disconnecting the camera cable must be done after turning OFF the Power of Camera Control Unit. [Rear Panel] 20. Gen-lock Signal Input Connector (BNC) (VBS/HD) The color video signal of the camera is automatically synchronized to the gen-lock signal (Composite Signal, Black Burst Signal or Video Sync) when either signal is supplied to this connector. The gen-lock signal is used for system reference. Caution: If the gen-lock signal is jittery (as in the case of a VCR playback picture), the camera can not be synchronized properly. (External HD and VD Mode) The horizontal and vertical pulse of the color video signal is synchronized to the external HD fed to this connector and external VD fed to the VD Input Connector (21). 21. Gen-Lock Signal Input Connector (BNC) (VD) Supply the external vertical drive (VD) pulse to this connector. 22. Gen-Lock Video 75 ohms Termination On/Off Switch (75 ohms ON/OFF) When looping through the gen-lock video signal with BNC *T“ Adaptor, set this switch to OFF position. When not looping through, set this switch to ON position. 23. Video Output Connector (BNC) (VIDEO OUT 1,2) A 1.0Vp-p/75 ohms composite video signal is provided at this connector. -5- 24. S-Video Output Connector (S-VIDEO OUT) The luminance(Y) and chrominance(C) signals for S-VHS VCR or monitor are provided at this connector. S-VIDEO OUT (Mini-DIN,4-pin) Pin No. Description 1 Y Ground 2 C Ground 3 Y Signal Output(0.714Vp-p(Y level)/75 ohms) 4 C Signal Output{0.286Vp-p(Burst Level)/75 ohms) CAUTION : CONNECT THIS TO A 12V DC CLASS 2 POWER SUPPLY ONLY. Caution : To prevent fire or shock hazard, the UL listed wire VW- 1, Style 1007 should be used for the cable for 12V DC Input connector. INSTALLATION Caution : Keep the Power ON/OFF Switch (4) of camera control unit in the OFF position throughout the installation. 25. RGB/SYNC Output Connector (D-SUB,9~pin) (RGB/SYNC OUT) Tho red, green, blue; sync and composite video signals are provided at this connector. Pin No. Description 1 Ground(GND) 2 Ground(GND) 3 Red(R) 0utput(0.7Vp-p/75 ohms) 4 Green(G) Output(0.7Vp-p/75 ohms) 5 Blue(B) Output{0.7Vp-p/75 ohms) 6 Composite Video Output(1,OVp-p/75 ohms) 7 Sync(SYNC)Output(4.0Vp-p or 0.3Vp-p/75 ohms) 8 Ground(GND) 9 Ground(GND) 26. 12V DC Input Connector(XLR,4-pln)(DC 12V) This connector accepts an external DC power source supplying nominal power of 12V DC, 0.7A. Lens Mount 1. Remove the front cap of the camera head and confirm that the surface of the optical filter of the camera head is clean. If the surface of the optical filter is dirty or dusts, clean it up with a blower brush which is for film camera lenses (available at your local camera store). 2. Mount the C-Mount Lens by turning it clockwise onto the lens mount of the camera head. Caution: • Do not use any lens which has more than 1/8" (3.5mm) of protrusion for lens mounting. • Do not open the lens iris greater than the F2.8 stop. (Less than 3.5 mm) Pin No Description 1 Ground(GND) 2 Not Used 3 Not Used 4 + 12VDCIN DC 12V (XLR,4-pin) -6- CONNECTIONS Cautions : 1. Keep the Power ON/OFF Switch (4) in the OFF position until all connections have been properly made. 2. Connect the camera head and camera control unit which are packed in the same box (a pair) otherwise it would be cause a improper operation. Internal Sync Operation 1. Connect the camera cable between the camera head and the camera control unit. 2. Connect the coaxial cable with BNC connectors between the Video Output Connector (23) of the camera control unit and the video monitor or VCR Video Monitor VTR or Video Monitor VIDEO VIDEO 75П Hi-Z 75П Hi-Z Coaxial @ © © Cable IN OUT IN OUT CCU © ШзЩ UJ TU Gen-lock Operation 1. Connect the camera cable between the camera head and the camera control unit. 2. Connect the coaxial cable with BNC connectors between the Video Output Connector (23) of the camera control unit and the Video Input Connector of Special Effects Generator (SEG), and between the VBS/HD Input Connector (20) of the camera control unit. 1 on 9V V » lOf 0 tu VBS/HD in VIDEO OUT 75ÎÎ set to ON Со) (63 (О) (Ю) ПГ Black Burst Out VBS/HD In VIDEO Out 75ÍÍ set to ON ““Video In Special Effects Generator (SEG) CCU Ü CCU "D ...