Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Wall Box Wood Siding Board Strong enough to support the camera weight (approx. 3 kg {6.60 lbs}) . Wood Siding Board Concrete slab Concrete slab . Concrete Template (provided) Wall 1 Make four holes in the wall using the template (provided). Protection Cover (provided) Part to be cut 2 Wrap the camera cables with the Protection Cover (provided) as appropriate to the Diecast Case. INSTALLATION Cut here 4 Cut the Diecast Case as shown. Note: Be sure to protect the Video and Power Cables with the Protection Cover (provided). Mounting Screw Rotate 15° Remove the Camera Mounting Base by pulling up. 3 Remove the Mounting Screw (M3, provided), pull up the Camera Mounting Base off the camera, and turn the camera counterclockwise. The Wall Mount Bracket WV-Q118 is provided for mounting the Combination Camera WV-CS950 or WV-CS954 onto the wall. There are various ways of installing the camera as shown below. Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use. • Fasten the bracket to a ceiling strong enough to support the camera weight (approx. 3 kg.{6.60 lbs}). • Wipe the bracket regularly using a soft and dry cloth, or a cloth moistened with a water solution of an ordinary kitchen detergent. • Do not use chemicals for cleaning the enclosure as it may damage the surface. • All the necessary steps required for installing this product must be taken by a qualified service person or system installer. PRECAUTIONS • Be sure to use the Fall Prevention Wire. • Do not use this bracket with any equipment other than the WV-CS950 and the WV-CS954. • Follow all applicable local and national electrical, fire and safety codes when installing the camera with this ceiling mount bracket. The model numbers in this Operating Instructions are shown without suffix. ........................................................ Decoration cover (1) Decoration cover (2) 5 Remove the Decoration Cover in order (1) then (2). The Decoration Cover can be removed by pressing on the points (1) at one place, and (2) at 4 places. 6 Fix the Camera Mounting Base (provided with the camera) to the bracket with the four M4- L8 Screws (provided). Note: Be sure to fix the Camera Mounting Base in the up direction as shown. Clamp 7 Run the cable around the outside and secure it with the clamp. Secure the cable with the clamp so it goes along the inside of the top case so it does not get in the way when attaching the case and installing the camera. 8 Attach the top case to the wall and run the cables. Attach it with four screws. Screws are not provided. Align it with the position the camera will be installed. Decoration cover (2) 9 Place the removed Decoration Cover(2) back on the bracket and camera. Note: Push the Decoration Cover up till it fits over the bracket with a click. Ring of the Fall Prevention Wire 10 Suspend the Fall Prevention Wire from the Camera Mounting Base. Notes: • Make sure that the wire matches the Fall Prevention Wire Fixing Angle. • The bracket is not shown in the illustration. 15° Camera Mounting Base Camera Rotate Press up 11 Attach the camera to the Camera Mounting Base, turn the camera clockwise, and tighten the Mounting Screw (M3, provided). Notes: • Tigthen the Camera Fixing Screw with a screwdriver. • In attaching the camera to the Camera Mounting Base, loosen the Camera Fixing Screw (M3), then tighten it back with a screwdriver while keeping it pushed up. • The bracket is not shown in the illustration. Decoration cover (1) 12 Place the removed Decoration Cover (1) back on the bracket and camera. Note: Push the Decoration Cover up till it fits over the bracket with a click. Ambient Operating Temperature: 10.C - +50.C {14.F – 122.F} Dimensions: 165 (W) x 140 (H) . 217.5 (D) mm {6-1/2” (W) x 5-33/64” (H) . 8-37/64” (D)} Weight: 650 g {1.43 lbs} Weight and dimensions indicated are approximate. Specifications are subject to change without notice. SPECIFICATIONS STANDARD ACCESSORIES Screw (M4-L8) ..................................................... 4 pcs. Template ................................................................. 1pc. Protection Cover ..................................................... 1pc. © 2005 Matsushita Electric Industrial Co., Ltd. All rights reserved. For European and other fields: Matsushita Electric Industrial Co., Ltd. Osaka, Japan For U.S. , Canadian and Puerto Rican fields: Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America Security Systems For customer support, call 1.877.733.3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630 PANASONIC CANADA INC. 5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Ca...