Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TO CHANGE AN EXISTING, KNOWN PIN If the existing PIN is known, it may be changed by one person without using a ladder. 1. Press the four buttons for the present PIN, then press and hold the # button. The opener light will blink twice. Release the # button. 2. Press the new 4-digit PIN you have chosen, then press ENTER. The motor unit lights will blink once when the PIN has been learned. Test by pressing the new PIN, then press ENTER. The door should move. TO SET A TEMPORARY PIN You may authorize access by visitors or service people with a temporary 4-digit PIN. After a programmed number of hours or number of openings, this temporary PIN expires and will no longer open the door. It can be used to close the door even after it has expired. To set a temporary PIN: 1. Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold the . button. The opener light will blink three times. Release the button. 2. Press the temporary 4-digit PIN you have chosen, then press ENTER. The opener light will blink four times. 3. To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press .. OR 3. To set the number of openings this temporary PIN will work, press the number of times to open (up to 255), then press #. The opener light will blink once when the temporary PIN has been learned. Test by pressing the four buttons for the temporary PIN, then press ENTER. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening. To clear the temporary password, repeat steps 1-3, setting the number of hours or times to 0 in step 3. SPECIAL NOTE: The temporary password can ONLY be programmed to Keyless Entries working on a 315 MHz Chamberlain or LiftMaster Garage Door Opener. It WILL NOT work on Keyless Entries programmed to an external receiver. The temporary password will continue to CLOSE the door even after the time has expired. To eliminate this, program a new temporary password into the Keyless Entry. THE KEYLESS ENTRY BATTERY To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. WARNING For a one-piece door, (SECTIONAL DOOR ONLY) choose the optional KEYLESS ENTRY MUST BE location shown in the SIGHT OF THE DOOR Door Jamb Face INSTALLATION Keyless Entry INSTALLED WITHIN Typical Installation 1. Choose a convenient location for installation. Exterior Front Wall Install out of the reach 1-Piece or Sectional Door of children at a minimum height of 5 Door Jamb Edge (Optional) feet (1.5 m), away from all moving parts of door. illustration to avoid injury as the door swings up and out. Test the reception of the Keyless Entry by operating your opener from the selected location. Change the location if necessary. 2. Remove the battery cover to access the bottom mounting hole. Slide the cover down to remove. Remove battery. 3. Center the keypad at eye level against the selected location. Mark 4-1/4" (10.8 cm) up the centerline from the bottom and drill a 1/8" (3.2 mm) pilot hole. Install top mounting screw, allowing 1/8" (3.2 mm) to protrude above surface. Position keypad on screw head and adjust for snug fit. With cover open so bottom mounting hole is visible, Mark the position of the hole. Remove keypad and drill 1/8" (3.2 mm) pilot hole. Replace keypad and complete installation with bottom screw, using care to avoid cracking plastic housing. Do not overtighten. Reinstall battery and replace the battery cover. To replace battery cover slide up and snap it into place. KEYLESS ENTRY MOUNTING (For reference only.) 4 1/4" The battery should produce power for at least one year. Replace when the Keyless Entry illumination becomes dim or it doesn’t stay on after a keystroke. Dispose of old battery properly. Top Cover Bottom Mounting Hole 9V Battery Battery Cover Replacement parts: Keypad cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D542-2 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A25 Battery cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D541 FOR SERVICE DIAL OUR TOLL FREE NUMBER: U.S. 1-800-528-2817 Canada 1-800-654-4736 © 2006, The Chamberlain Group, Inc. 114A3039B All Rights Reserved 1. Enfoncer et tenir le bouton LEARN sur le moteur. Le temoin lumineux learn s’allumera en continu pendant 30 secondes 2. Dans un delai de 30 secondes, introduire un numero d’identification personnelle (NIP) a quatre chiffres de son choix sur le pave numerique. Enfoncer et tenir ensuite le bouton ENTER. 3. Relacher le bouton lorsque l’eclairage du moteur clignote. Il a appris le code. Si...