Évaluations - 4, GPA: 5
(
)
)
|
Facilité d'utilisation
• In General interface please input upload interval. • In Detect interface please enable snapshot function for specified channels. Or in alarm interface please enable snapshot function for specified channels. Please refer to the following figure for detailed information. Figure 4-14 Activation Snapshot Setting Priority Please note the activation snapshot has the higher priority than schedule snapshot. If you have enabled these two types at the same time, system can activate the activation snapshot when alarm occurs, and otherwise system just operates the schedule snapshot. Image FTP In Network interface, you can set FTP server information. Please enable FTP function and then click save button. Please boot up corresponding FTP server. Please enable schedule snapshot or activation snapshot first, now system can upload the image file to the FTP server. After the system has booted up it will enter a default 24-hour regular mode. You can set the record type and time in schedule interface. Detect Go to Detect Menu In the main menu, from Setting to Detect, you can see motion detect interface. There are three detection types: motion detection, video loss, camera masking. Motion Detection The detection menu is shown as below. See Figure 4-15. • Event type: From the drop-down list you can select the “Motion Detection” type. • Channel: Select the video channel for the motion detection setting. • Record Channel: Select the channel to activate the recording function once the alarm has sounded. Please make sure you have set the MD recording in the schedule interface (Main Menu.Setting.Schedule) and automatic recording in manual record interface (Main Menu- >Advanced->Manual Record) Overview of Navigation and Controls 42 • Delay: When detected motion is completed, the system will continue alarm output and recording for a specified time respectively. The value ranges from 10-300(Unit: second). • Region: Click Select, the interface is shown as in Figure 4-16. Here you can set the motion detection zone. There are 396(PAL)/330(NTSC) small zones. • Sensitivity: The system supports 6 levels. The sixth level has the highest sensitivity. The fifth or lower levels are recommended to avoid setting a false alarm. • Show message: The system will send message to the local host screen to alarm you if you have enabled this function. • Send email: The system can send out an email to alert you when the alarm occurs. • PTZ activation: Here you can set PTZ movement (of any video channels) such as going to a preset when motion is detected in the current video channel. Click Select, and you can see an interface is shown as in Figure 4-17. • Period: Click Set to determine the period for the channel to be armed for motion detection. See the interface shown as in Figure 4-18. Here you can set for business days and non-business days. In Figure 4-18, click Set, and you will see an interface as shown in Figure 4-19. Here you can set your own business day and non-business day. • Alarm output: After the motion detection has occurred, the system enables the peripheral alarm devices. • Tour: Here you can enable the tour function when the alarm occurs. It is a one-window tour. Please go to Display for tour interval setup. Note If there are record channels selected, only the record channels will be displayed in the tour. Check boxes to select the corresponding function. After all the settings, click Save, and the system will return to the previous menu. Note In Figure 4-16, you can left click the mouse and drag it to set a region for motion detection. Click Fn to switch between arm/withdraw motion detection. After setting the region, click the enter button to exit. Figure 4-15 Motion Detection Menu Figure 4-16 Motion Detection Zone Setting Figure 4-17 PTZ Activation Setting Figure 4-18 Armed Period Setting Figure 4-19 Business Day and Non-Business Day Setting Video Loss In Figure 4-15, select “Video Loss” from the type list. You can see the interface is shown in Figure 4-20. This function allows you to be informed when video loss has occurred. You can enable the alarm output channel and enable the show message function. Tips: You can enable preset activation operation when video loss occurs. See Motion Detection for detailed information. In “Detect” interface, the copy/paste function is only valid for the same type, which means you cannot copy a channel setup in video loss mode to camera masking mode. Figure 4-20 Menu of Video Loss Camera Masking When someone viciously masks the camera lens, the system can alert you to guarantee video continuity. Camera masking interface is shown as in Figure 4-21. Tips: You can enable preset/tour/pattern activation operation when video loss occurs. See Motion Detection for detailed information. Note Figure 4-21 Menu of Camera Masking Alarm Setup and Alarm Activation Before operation, make sure you have properly connected alarm devices such as the buzzer. Go to alarm setup interface On the main menu, from Setting to Alar...
Ce manuel est également adapté pour les modèles :Vidéo - HD-DVR-1008 (4.96 mb)
Vidéo - HD-DVR-1016 (4.96 mb)