Log:
Évaluations - 2, GPA: 4 ( )

Instructions Haier, Modèle FCD-JTHC60-E

Fabricant : Haier
Taille : 2.18 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


The power socket shall meet national standard requirements. Power plug pins shall be cleaned in time to avoid any contamination causing accidents like fire. Do not use damaged wire, socket or appliances with loose plug, otherwise accidents like electric shock, short circuit and fire may occur. Make sure power plug closely fits with power socket. .....».. Power socket for water heater shall be located in a dry place free of water spray. Do not insert or pull the power plug with wet hands, for accidents like electric shock or injury may happen. For first use after installation, the tank must be full of water before connecting the power. Otherwise, heating element overheat may cause troubles.Children taking shower must be attended by adults. Please do not point the showerhead towards human body when turning on or off the faucet, avoiding to be scalded by a small stream of hot water. Connect to drain hose Never do that Be sure to act as per instructions Description of the Symbols Connection and Use of Safety Valve: The safety valve should be connected to the cold water inlet pipe. Please check carefully if the direction is correct after installation. The correct direction of installation is that the arrowhead on the safety valve should point to the water heater. If your water heater is not installed in a bathroom with sewage drain, please connect the drain hose to the safety valve. Connect one end of the hose to the safety valve vent and the other end to the sewage drain. The hose can be cut short or extended as necessary. The hose shall be installed as inclined downward. The water may drip from the discharge pipe of the pressure relied device and that this pipe must be installed in a continuously downward direction and in a frost-free environment. Check safety valve once a month as follow: move the small handle of safety valve, if there's water flowing out, safety valve is normal; if there's no water flow, please contact local after-sales service station. The pressure relief device is to be operated regularly to remove lime deposits and to verify that it is not blocked. . »O .° .. °O UI .· .A AE ®. A. O· . Do not install it outdoors. Do not install it as stand-alone. It shall be hung on firm and solid wall. Do not install it in places unable to drain water. Installation must be made by installers of or designated by our company after-service department. The water heater shall be wall-mounted. Before installation, make sure water heater rear wires are fit firmly. Determine an installation location. Make four holes§.12mm, 65 mm dee pin the wall. Insert and fix expansion hooks and expansion bolts in corresponding wall holes. Lift the water heater. Insert wall rack onto the hooks and bolts. Fit flat washers, rear wires and nuts in turn onto the bolts. Tighten the nuts and check them firm. Install accessories such as safety valve, drain hose as shown in Fig. 2. Use sealing compound to prevent water leakage. To facilitate installation and removal, it is suggested a G 1/2" movable nut is fitted at appropriate locations on inlet and outlet pipes respectively. Find water supply location. Connect inlet pipe, outlet pipe and city water pipe respectively to the use point. Note: To avoid heat dissipation, hot water pipe shall not be too long. For easy future maintenance and repair, adequate space must be reserved during installation. (Fig.3) The tubes and pipes fitted on the product are inseparable parts of the Safe Care technology, and shall not be removed by yourself. Otherwise, Haier shall not be liable for any damages or injuries caused due to resulted potential risks. Do not locate in freezing places. If ice forms, tank and pipes will break, causing scalding and leakage. If a drain hose is connected, it shall be connected to sewage drain, avoiding spilling the room. Hot water valve C...

Ce manuel est également adapté pour les modèles :
Chauffe-eau - FCD-JTHC50-E (2.18 mb)
Chauffe-eau - FCD-JTHC40-E (2.18 mb)
Chauffe-eau - FCD-JTHC80-E (2.18 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories