Log:
Évaluations - 5, GPA: 4 ( )

Instructions Haier, Modèle QBJ1-175A58E

Fabricant : Haier
Taille : 524.12 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Unpacking the tank, rip off the protection film. Uninstall the nut and cushion. 2. Place tank onto tank bracket cradle, inserting protruding bolts into holes. fasten with nuts. Notice: 1. Rip off the protection film after the installation to avoid the destroy of the tank, and please don't use the sharp tool. 2. Leave nuts loose since some adjustment may be necessary after fitting tubes. 3. When assembling the water tank, keep the center line of vacuum tubes connecting holes parallel with the diagonal pillar of bracket. Frame assembly Please consult the accessional paper for figure of the frame and packing list in the packing of frame. Frame fastness 1. Peg the feet of the heater into the earth with prepared iron or into the concrete brick with intumescent bolt. 2. Adjust the height of the frame with the water-proof cushion to keep the tank aclinic and each foot balanceable. Notice: 1. Make sure that the feet are all attach the floor closely, or it will cause the distortion of the frame. 2. Please use the tight wire to fasten the tank and frame in the area that the typhoon occurred frequently. 3. The installation of the solar water heater should be steadily or it will cause the destruction and the accident. 5 Assembly Instruction Assembly Instruction Glass tube assembly 1. Keep tubes out of the irradiation while assembling the unit or a scald may be caused. 2. Place the rounded side of rubber seal downwards on the open end of tubes.(A) 3. Insert the tube into base support of locating hole with gentle pressure and twisting motion. 4. Holding the tube, fix base support into base bracket (B), insert tube into base support (C). 5. Slide the tube down 1 cm, Slide black rubber seal up the tubes until it sits flush with tank(D). 6. Insert one tube on either end of the tank to achieve alignment of unit. Notice: 1. Make sure the silicon seal ring are clean and well positioned. 2. Place the rounded side of rubber seal downwards on open end of tube. Slide it down 10 cm. Wet open end of tube to make it easier to insert. Silicon seal ring Evacuated tubes Base support Evacuated tubes Base bracket Rubber seal AC Base bracket Rubber seal hold position Base support BD 6 Assembly Instruction Assembly Instruction Extraventricular plumbing instructions Air supply pipe Over flow pipe Over flow hole ( conect to the room A Inlet/outlet hole (1/2 ), conect to the room Air supply hole(1/2 ) forbidden to stem QBJ1-130A58E QBJ1-150A58E QBJ1-175A58E QBJ1-200A58E A b a Electric heating flange a b Sensor hole 3/4 Sensor Electric heating pipe QBJ1-230A58E QBJ1-270A58E Remarks: The permitted error limit of above parameters is 10%. Indoor plumbing instructions 7 Connect racing belt the line of tWater level sensor Electric heating Pre-burrided cord slot Solar water heater Hot water Tap water Controller Assembly Instruction Assembly Instruction Installation notice 1. Any alteration to the structure of the solar water heater may cause the trouble while using it. 2. There are 5 conne...

Ce manuel est également adapté pour les modèles :
Chauffe-eau - QBJ1-130A58E (524.12 kb)
Chauffe-eau - QBJ1-150A58E (524.12 kb)
Chauffe-eau - QBJ1-200A58E (524.12 kb)
Chauffe-eau - QBJ1-230A58E (524.12 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories