Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
. . . . . . . . . . . . . .2 Installation Instructions . . . . . . . . . . . . . . . . .3–4 Maintenance Instructions . . . . . . . . . . . . . . . . .5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .5 Assembly of Components . . . . . . . . . . . . . . . .6 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 IMPORTANT This equipment should be inspected, tested, and recorded weekly to maintain proper operation. Read this installation manual thoroughly before beginning installation. This installation manual should be filed by the owner’s maintenance department. P.O. Box 309, Menomonee Falls, WI 53052-0309 215-084 Rev. L; EN 02-586 TEL. 1-800-BRADLEY FAX 262-251-5817 Page 1 of 6 10-Gallon Tank with Eye Wash and Optional Heater Jacket S19-690LHS, S19-690H Installation Instructions Pre-Installation Information Operation The Bradley 10-Gallon Tank provides emergency protection in areas where permanent water supply is not available. After emergency use of the portable unit, further cleansing of the injury should be administered at a conventional plumbed fixture. Components 10-Gallon Tank: The stainless steel tank has built-in carrying handles. The tank has a tire filler valve with 0-160 PSI air gauge. Pressure relief valve prevents accidental over-pressurization. (NOTE: Do not exceed 130 PSI tank pressure.) Empty tank weighs 23 lbs., 86 lbs. full. Eye Wash: The twin chrome-plated, soft flow eye wash heads have automatic flow control and stay- open valve. Flow maintained approximately 15 minutes from eye wash. Optional Heater Jacket: The insulated heater jacket is made of yellow 200-Denier foam-backed nylon and has a clear vinyl pocket to house the junction box. The eye wash yoke is wrapped with a heat trace cable and lined with pipe insulation for further freeze protection. Silicone rubber drum heaters have tension spring and hook fasteners. The heater jacket thermostatically controls water in weather conditions down to -10°F (-23°C). Supplies Required • pipe sealant • Air pressure equipment or supply Check Contents Separate all parts from packaging and check each part with Figure 2 and the parts list on page 6. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to assemble your Bradley 10-Gallon Tank until you obtain the missing parts. Bradley 10 Gallon Tank Warranty Bradley Corporation warrants to commercial and institutional purchasers only each fixture free from defects in material and workmanship under normal use and service upon the following terms and conditions: 1. We will replace, without charge, any part which proves to be defective within one year from the date of our invoice at our option, F.O.B. Menomonee Falls, Wisconsin. 2. This warranty does not cover installation or any other labor charge and does not apply to fixtures which have been damaged by accident, abuse or improper maintenance. 3. The repair or replacement of the defective fixtures as stated in this warranty shall constitute the sole remedy of the purchaser, and the sole liability of the Bradley Corporation under this warranty. Bradley Corporation shall not otherwise be liable under any circumstances for incidental, consequential or indirect charges caused by defects in fixtures or any delay in the repair or replacement thereof. 4. This warranty extends only to commercial and institutional purchases and does not extend to any others, including consumer, customers of commercial and institutional purchasers. 5. This warranty is in lieu of all other warranties expressed or implied, including any implied warranty of merchants ability or fitness for a particular purpose, or otherwise. 6. Bradley emergency fixtures are to be used as a supplement to first aid treatment. Bradley Corporation cannot guarantee that when used this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries. No other warranties, expressed or implied are authorized, provided or guaranteed by Bradley Corporation. Bradley Corporation • 215-084 Rev. L; EN 02-586 10-Gallon Tank with Eye Wash and Optional Heater Jacket Installation Instructions S19-690LHS, S19-690H Installation Instructions Step 1: Install eye wash 1. Attach the eye wash to the tank outlet with pipe sealant (supplied by installer) (see Figure 1). IMPORTANT: When attaching the eye wash to the tank outlet, hold the adapter (Item 3) with a wrench to prevent stripping. Failure to do so may damage the seal and cause leakage. 2. Attach the pressure gauge to the adapter on the pressure side of the tank with pipe sealant (supplied by installer) as shown in Figure 2 on page 6. 3. FOR OPTIONAL HEATER JACKET: • Secure the pipe insulation and yellow jacket to the eye wash assembly. • Wrap the heater belt arou...
Ce manuel est également adapté pour les modèles :Chauffe-eau - S19-690LHS (44.38 kb)