Évaluations - 2, GPA: 4 ( )

Fabricant : Desa Taille : 4.93 mb Nom Fichier : Langue d'enseignement:

See Figure 30 for CCL3924PTA/NTA or CCL3930PTB/ NTB. See Figure 29, page 15, for CCL3018PA/NA or CCL3018PTA/NTA. 7. For CCL3930PTB/NTB only: Locate holes on the bottom of crossover log (#7). Slide onto the pins located in crossover log (#6) and middle log (#2). See Figure 31. 8. Add lava rock around base of heater if desired. Do not place any lava rock on logs or burner. Crossover Log (#6) Crossover Log (#7) 111160-01B Forr morre iinfforrmattiion,, viisiitt 1177 INSTALLATION Installing Logs (Cont.) OPERATING HEATER (Manually-Controlled Models ) Figure 33 - Installing Front Log Front Log Grate Fingers Figure 34 - Installing Crossover Log Post INSTALLATION Continued Post Base Assembly Crossover Log Hole in Back Log Hole in Front Log OPERATING HEATER FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. WARNING • If fireplace has glass doors, never operate this heater with glass doors closed. If you operate heater with doors closed, heat buildup inside fireplace will cause glass to burst. Make sure there are no obstructions across openings of fireplace. • You must operate this heater with a fireplace screen in place. Make sure fireplace screen is closed before running heater. NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours. LIGHTING INSTRUCTIONS MANUALLY-CONTROLLED MODELS 18 18 OPERATING HEATER (Manually Controlled Models) Lighting Instructions (Cont.) Variable Control Operations To Turn Gas Off to Appliance OPERATING HEATER Continued Note: Home owners generally prefer to operate their heater with the chimney damper closed. This will put all the heat into the room. However, there may be times you will desire the full flames of the HI heat setting but will find the heat output excessive. You can open the chimney damper (if you have one) fully or partially to release some of the heat. WARNING: Damper handle will be hot if heater has been running. 1. STOP! Read the safety information in column 2, page 17. 2. Make sure equipment shutoff valve is fully open. 3. Press in and turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, column 2 on page 17. If you don’t smell gas, go to the next step. 5. Slightly depress and turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 35). Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system. PILOT OFF LO HI Ignitor Button Control Knob Figure 35 - Control Knob and Ignitor Button Location Pilot BurnerIgnitor Electrode Thermocouple Figure 36 - Pilot 6. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the burner. If needed, keep pressing ignitor button until pilot lights. Note:If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 19. 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note:If pilot goes out, repeat steps 3 through 7. If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs. 8. Slightly depress and turn control knob counterclockwise to desired heating level. The burner(s) should light. Set control knob to any heat level betwe...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :