Évaluations - , GPA: ( )

Instructions Kenmore, Modèle 350 Series

Fabricant : Kenmore
Taille : 3.15 mb
Nom Fichier : 625.393560.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

(May recharge more often using smaller salt dosage and less water). When installing this unit in the State of California, this setting MUST be ON. FIG. 34 California Efficiency Requirement Your Kenmore Water Softener has a “High Efficiency” feature with an “ON” or “OFF” setting. This softener setting is shipped in the “OFF” position, which utilizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn this setting to the “ON” position which may initiate more frequent recharges, however it will operate at 4000 grains per pound of salt or higher. 2. Press SELECT again to show the CLEAN display. Clean. This feature is beneficial on water supplies containing iron and/or high amounts of sediments (sand, silt, dirt, etc.). When set to ON, a backwash and fast rinse cycle will occur first, preceeding the normal regeneration sequence (see pages 26 - 28). This provides extra cleaning of the resin bed before it is regenerated with the salt brine. To conserve water, if your water supply does not contain iron or sediments, be sure this feature is set to OFF. The default is OFF. 3. Press SELECT again until the CLEAN TIME display FIG. 35 shows. Clean feature minutes: If you are using this feature, the length of the extra backwash cycle automatically is set to 7 minutes. However, you can adjust this time from 1 to 15 minutes in length. To change this cycle Default Minutes Example: time, use the UP button to increase, the time, or the Time Set to 3 Minutes DOWN button to shorten the time. If no change is desired, continue to next step. FIG. 36 Questions? Call The Kenmore Water Line 1-800-426-9345 Faceplate Timer Features 4. Press SELECT again to show the following RECHARGE display. EXAMPLE: Set to 4 days maximum between regenerations. Maximum Days Between Regenerations: The face plate timer automatically controls regeneration frequency. This provides the greatest operating efficiency, and under most conditions this feature will be left in its default mode. However, you can modify this feature if you want to force a regeneration every set number of days. For example, if your water supply contains iron and you want the softener to regenerate at least once every few days to keep the resin bed clean, set the display as typically shown above. Setting is available from 1 to 6. Press SELECT to return to the present time is play. 5. Press SELECT to show the 97% display. IntelliSoft 97% Feature: The 97% Feature is an integral part of the IntelliSoft water and salt saving system. When this feature is ON, the softener will automatically recharge when 97% capacity has been used, at any time of day. The default is ON. If this feature is not desired, turn it off by pressing the DOWN button. 6. Press SELECT to show the 12 HOUR display. 12 or 24 hour clock: All time displays are shown in standard clock time (1 to 12 PM; and 1 to 12 AM) at the 12 hr default setting. If Military time displays are desired, set to 24 hr by pressing the UP button. WATER FLOW THROUGH THE SOFTENER If soft water is in use, the water flow bars continually scroll across the display. The bars scroll slowly when water flow is slow, and move faster as water flow increases. The flow bars do not show when all faucets and water using appliances are off. DAY DAY RECHARGE RECHARGE Default Display Example: Set to 4 Days Maximum Between Regeneration RECHARGE RECHARGE AM PM TIME TIME Flow bars scroll when soft water is in use. FIG. 37 Questions? Call The Kenmore Water Line 1-800-426-9345 Faceplate Timer Features RECHARGE TIME REMAINING AND VALVE POSITION INDICATORS One of the valve position indicators (Serv, Fill, Brine, Bkwsh, Rinse) is displayed while the softener is recharging. RECHARGE flashes in the display and, beginning with Brine, the minutes of recharge remaining before return to service appears in place of the present time. When the valve is moving from one cycle to another, both position indicators are flashing. See Fig. 38. PROGRAM MEMORY If electrical power to the softener goes off, the time display is blank but the face plate timer keeps the correct time for about 6 hours. When electrical power comes on again, you have to reset the present time only if the display is flashing. The HARDNESS and RECHARGE TIME never require resetting unless a change is desired. Even if the timer is incorrect after a long power outage, the softener works as it should to keep your water soft. However, regenerations may occur at the wrong time of day until you reset the timer to the correct time of day. ERROR CODE An error code could appear in the face plate display if a problem occurs in the softener electronics. Turn to the Troubleshooting section to resolve the problem and/or call the Kenmore Water Line number listed below. KENMORE’S ULTRA CLEANSING FEATURE The ultra cleansing feature keeps larger particles of sediment from entering the home’s plumbing system. As water passes through the s...