Évaluations - 3, GPA: 4.3 ( )

Fabricant : Sears Taille : 1.36 mb Nom Fichier : b25138f2-b8f8-480a-8c08-53aa39771915.pdf Langue d'enseignement:

--You did not refill the softener with salt before it was gone. You can start a regeneration right away, or you can set the AM (or other following. timer to regenerate preset recharge at the time). next Do 2:00 the RECHARGE NOW • Press the ON/OFFHOLD button and holduntil mm RECHARGE NOW, SERV and FILL begin to flash in the display. Upon reaching fill, the first cycle of regeneration, the flashing SERV goes off and FILL is on steady. RECHARGE NOW continues to flash. This re generation will last for about 2 hours. After the 2 hours, you will have soft water again. RECHARGETONIGHT • Press and release (do not hold) the ON/OFF-HOLD $ llms button. RECHARGE TO-IImJ m4 NIGHT flashes in the dis-Ima_ m_ play, and the softener begins regeneration at the next preset recharge time. Press and release the ON/ OFF-HOLD button once more if you decide to cancel the regeneration, and RE CHARGE TONIGHT. SALT MONITOR SYSTEM The face plate timer has a low salt monitor with an indicator light to remind you to refill the storage tank with salt. To set this monitor system: 1, Lift the salt hole cover and level the salt in the storage tank. e The salt level decal, on the brinewell inside the tank, has numbers from 0 to 8 (see drawing on page 9 and below). Observe the number the leveled salt is at or closest to. NOTE: To light the salt storage area, press the TANK LIGHT button on the face plate. o Now, press the SALT LEVEL ADJUST button until black bars display up to the salt level number. For example, the pictures below show the salt level at 6. e Finally, set the level you want the low salt indicator light to come on. Press the SIGNAL LIGHT ADJUST button until a (.) shows opposite this number. In the example below, the light will come one when the stored salt drops to level 2. At level 2, the storage tank is about 1/3 full. This is the lowest you should allow the stored salt level to drop to. To turn the salt monitor off, press the button until OFF shows. indicator light / MONITORs,,, \0 SYSTEM brinewetl m SALT LEVEL 8_ decal salt 7 I level m3 m2_ 6 / black boxes NOTE: For accurate salt monitor operation, always use nugget or pellet water softener salt. See page 9. 10 SECTION 2 HOW YOUR WATER SOFTENER WORKS 2A. FACE PLATE TIMER FEATURES TANK LIGHT PROGRAM MEMORY _.__;__._ 2.UU n, To light the inside of the salt If electrical power to the softener goes off, the storage tank, press the TANK time display is blank but the face plate timer LIGHT button on the face keeps the correct time for about 72 hours. When plate. Press the same button I-'iI _ .nn electrical power comes on again, you have to again to turn the light off, or it reset the present time only if the display is will go off automatically in 4 tank light ON flashing. The HARDNESS and RECHARGE indicator minutes. TIME never require resetting unless a change is desired. WATER FLOW RATE THROUGH THE SOFTENER To view the gallon per minute water flow rate Even if the timer is incorrect after a long power through the softener, if not already displayed, outage, the softener works as it should to keep press the #2 SELECT button. your water soft. However, regenerations may If soft water is being used, the occur at the wrong time of day until you reset the flow rate to the closest 1/10 timer to the correct time of day. T 8 gallon shows. If all faucets ERROR CODE and water using appliances An error code could appear in I _,r,_I are off, the display will show 0 _rr_ flow. problem occurs in the softener { AVERAGE DALLY GALLONS electronics. If you see an error ""1"o;_ I,,{, ! I_ the face plate display if a [_;_i! Press the #2 SELECT button code instead of the present .__ again to show the average time of day, please call you number of gallons of soft wa-local Sears Service Departter the household uses each ment for service. day. This water usage figure is adjusted daily by the face plate timer. To turn this display off, press the #2 SELECT button once more. 11 SECTION 2 HOW YOUR WATER SOFTENER WORKS 2B. SOFT WATER SERVICE SERVICE When the softener is giving you soft water, it is called "Service". During service, hard water comes from the house main water pipe into the softener. Inside the softener resin tank is a bed made up of thousands of tiny, plastic resin beads (FIG. 4). As hard water passes through the bed, each bead attracts and holds the hardness minerals. This is called ion-exchanging. It is much like a magnet attracting and holding metals. Water without the hardness minerals (soft water) flows out of the softener and into the house soft water pipes. After a period of time, the resin beads become coated with hardness minerals and they have to be cleaned. This cleaning is called regeneration or recharge. Regeneration is started at 2:00 a.m. by the electronic timer (see page 14). It takes place in 5 stages or cycles. These are: _-1 FILL [] BACKWASH [] BRINING [] FAST RINSE [] BRINE RINSE WATER FLOW THROUGH THE SOFTENER IN SERVICE Hard Water IN Soft Water OUT Resin Tank ..----Resin Be...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :