Log:
Évaluations - 4, GPA: 3.8 ( )

Instructions GE, Modèle HAZER 2

Fabricant : GE
Taille : 745.14 kb
Nom Fichier : Arena_Hazer2_UM.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. . Never connect the device to a dimmer pack. . Make sure the power cord is never crimped or damaged. . Never disconnect the power cord by pulling or tugging on the cord. . Avoid direct eye exposure to the light source while it is on. . Use only water-based fog fluid. Do not use oil based fluid. 2. INTRODUCTION Features . 2-channel DMX professional hazer . Adjustable haze output via wired remote or DMX . Adjustable blower speed via wired remote or DMX Additional Features . Adjustable blower angle . 3-pin and 5-pin DMX connections . Wired remote with LCD screen . 2.5 L tank capacity . 8 min heat up . Low fluid indicator and auto shut down . LED-illuminated tank . Water-based hazer DMX Channel Summary CHANNEL FUNCTION 1 Blower 2 Haze Product Overview Power switch Power in Breaker Carrying handle Wired remote with LCD backlit control panel Blower 3-pin DMX in/out 5-pin DMX in/out LED-illuminated tank Door latch Product Dimensions 3. SETUP AC Power This fixture runs on either 115 VAC, 60 Hz, or 230 VAC, 50 Hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0 to 100% switch. CAUTION B&W Triangle - 200x184.gif To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its average current draw under normal conditions. CAUTION B&W Triangle - 200x184.gif Always connect the fixture to a circuit with a suitable electrical ground. Breaker Reset This product is equipped with a breaker on the main power input, located on the exterior of the back panel. In the event that this breaker trips, you may reset it very easily. 1. Unplug the product from the power outlet. 2. Allow to cool for 5~15 min. 3. Press on the breaker button until it remains in place. Important Icon - B&W - 200x201.gif In the event that this breaker will not reset, contact CHAUVET for troubleshooting. The fixture may need to be serviced. LED-Illuminated Tank The fluid tank on this hazer is equipped with LEDs, in order to provide visual fluid level indication, as well as to provide the readiness of the hazer. When the color is at red, it means that the hazer is heating. In most circumstances, this will not prevent the hazer from operating. During operation, the color of the tank will periodically change between blue and red. When initially powering on the hazer, the tank color will be red. This means that it must heat up to operating temperatures. Once the maximum operating temperature is reached, the tank color will be blue. This hazer is designed to work continuously at maximum haze output without the need to wait for the heater to warm up periodically. Important Icon - B&W - 200x201.gif When the tank is empty, the LEDs will flash blue to indicate the auto cut-off feature has been activated. 4. OPERATING INSTRUCTIONS Configuring the Starting Address Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the starting address. For example, a fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose the starting addresses for each fixture so that the channels used do not overlap. In addition, you should note the starting address selected for future reference. The Arena Hazer™ 2 fixture uses two DMX channels. If this is your first time using DMX, we recommend reading the “DMX Primer” section in the “Appendix”. Control Panel Functions Access control panel functions using the six buttons located underneath the LCD Display on the included wired remote. Button Function Used to select incremental fan speed, as well as select the DMX address in address selection mode Used to select incremental haze output Latching full fan speed and haze output Used to select to DMX address selection mode The Control Panel shows the current state of the unit. It also has a sub-menu, which is used for setting the DMX starting address. You may select any combination of incremental fan speed and haze output, using the respective <+> and <-> buttons. If an immediate full fan speed and maximum haze output is desired, press . This is a latching button. Control Panel Functions (cont.) DMX This operating mode will allow you to control the Arena Hazer™ 2 with an external DMX controller. You must set the starting address for this mode. If this is you...

Ce manuel est également adapté pour les modèles :
purificateurs d'eau - HAZER 2 (745.14 kb)
purificateurs d'eau - HAZER 2 (745.14 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories