Évaluations - , GPA: ( )

Instructions Kenmore, Modèle 625.34842

Fabricant : Kenmore
Taille : 2.98 mb
Nom Fichier : 3883e981-2ef6-4753-95ee-1ce464d3e63a.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

IF YOU HAVE QUESTIONS ABOUT CLEANING AND MAINTAINING YOUR SOFTENER, CALL TOLL FREE, NUMBER 1-800-426-9345. 15 SECTION 3 CARE OF YOUR SOFTENER I I 3C. KEEP THE SOFTENER FROM FREEZING If the softener is installed where it could freeze DRAIN WATER FROM THE (summer cabin, lake home, etc.), you must drain all SOFTENER water from it to stop possible freeze damage. To drain the softener: 1. Close the shut-off valve on the house main water pipe, near the water meter or pressure tank. 2. Open a faucet in the soft water pipes to vent pressure in the softener. e If a single bypass valve is installed, move the stem into bypass. See FIG. 12 on page 18. In a drain wood block 3-valve bypass system, close the inlet and outlet valve and open the bypass valve. If you want water in the house pipes again, reopen the Looking at FIG. ] ], lay a piece of 2 inch thick shut-off valve on the main water pipe. 8. board near the floor drain. Move the softener 4. Unplug the transformer at the wall outlet. close to the drain. Slowly and carefully, tip it over until the rim rests on the wood block with 5. Remove the salt hole cover and the main cover. the inlet and outlet over the drain. Do not allow Take off both drain hoses. the softener's weight to rest on the inlet and outlet fittings or they will break. 6. Carefully remove the large holding clips at the 9. softener inlet and outlet (see Key No. 6], on page Tip the bottom of the softener up a few inches and hold until all zuatc_ _has drained. Leave the 30). Separate the softener from the adaptors or bypass valve. softener laying like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, 7. Remove the brinewell cover and disconnect the bugs, etc. out. brine valve tubing at the nozzle and venturi assembly (see page 23). Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain out water. 16 SECTION 3 CARE OF YOUR SOFTENER I I 3D. HELPFUL HINTS CHECKLIST ... TO HELP YOU SAVE MONEY If your water softener fails to work, make the following easy checks. Often, you will find what's wrong yourself and you won't have to call and wait for service. If, after making the checks, your softener still does not work right, call your Sears Service Department, or call toll free, number 1-800-426-9345 for telephone assistance. NOTE: 1. Also read ERROR CODE, page ] 0. 2. If an error code is not dispIayed, press and bold the SELECT button until (example: 000--) shows in the display. Then, press SELECT again and bold until an SR code appears. It must show SR 17. If any other SR number shows, the softener computer is working on incorrect input and this would probably be the cause of the problem. To set SR 1.7, press either the UP (_ or DOWN[_buEon. Then, press SELECT to return a flashing 12:00 AM display, and reset the umer on page 6. PROBLEM CAUSE CORRECTION No soft water Faucet or fixture may be plumbed to From the outlet of the water softener, trace the water flow hard water paths in your house pipes. If soft water is not directed to a faucet or fixture where it is wanted, consult a plumber. To conserve salt, the installer may have isolated some fixtures (outside faucets, toilets, etc.) from soft water. No salt (or salt bridged) in the storage Refill with salt, or break the salt bridge (page 14). Press tank ON/OFF-HOLD (RECHARGE NOW) button and hold for 3 seconds to start a regeneration (see page 10). Transfomer unplugged at the wall Check for loss of power due to any of these and correct. outlet, or power cable leads loose, fuse With the power back on, look at the time display and read blown, circuit breaker popped, or circuit PROGRAM MEMORY, page 10. switched off. Manual bypass valve(s) in bypass Look at FIG. 12 on page 18. Move the stem in a single position valve to service. In a 3-valve bypass, open the inlet and outlet valves, and be sure to fully close the bypass valve. Dirty, plugged or damaged nozzle & Take apart and clean or replace damaged parts (see page venturi 15). Valve drain hose plugged The drain hose must not have kinks, sharp bends, or be raised too high above the softener (see page 16 in your installation manual). Water hard Hardness number setting too low Press and release the SELECT button until HARDNESS sometimes shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown on your water analysis report. See page 7 to reset. Press and release the SELECT button until the present time shows in the display. Using hot water when softener is Avoid using hot water during this time because the water regenerating heater refills with hard water (see Automatic Bypass, page 13). Increase in the grains of hardness in Ask your Sears retail or catalog store for a new water your water supply analysis. Then make a new hardness number setting (page 7). 17 SECTION 4 Ta,.GS OTaERTOW.OW II 4A. DIMENSIONS/SPECIFICATIONS BYPASS VALVES _F_ SINGLE-PLASTIC SINGLE-BRASS OUTWARD l .... FOR x" \ Push ...