Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Retain this manual for future reference. Always disconnect the power supply before servicing the unit. Do not operate the Unit without filter inserts. Contaminants in the extracted air will damage the blower. Use only original equipment filters. The BVX-208 is designed for the removal of solder fumes. Use filter unit only for this purpose. Consult your “safety department” when using the unit on flammable gases. This unit is not explosion safe and can only be used for the extraction of vapors, which have concentration levels well below the lower explosive limits. This system is equipped with automatic reset overload protection, which may cause the unit to restart automatically. While under warranty, the unit may be repaired only by an authorized Metcal Service Representative. Items Supplied 1 Filter Unit with filters installed 1 32mm hose adapter 1 air inlet cover installed on second air inlet port 1 Power Cord 1 Operating Manual Description (1) ON/OFF switch (2) Power Output (3) 32mm hose adapter (4) air inlet cover with bypass valve (5) latch (front and back) Installation • Place filter unit (1) at a location which minimizes length of ducting • Screw supplied hose adapter into open air inlet port (2) • Install ducting (3) as per duct installation instructions • Install iron adapter kits (4) • Connect filter unit to power supply (5) Operation and Maintenance • Turn unit ON. • Check if the motor pump indicates an acoustical “fluttering” effect. If yes, open air by-pass valve on air inlet cover until “fluttering” sound disappears. Do not open too much as this will reduce the airflow performance. The “fluttering” does not cause any damage to the system. Maintenance The airflow of the filter unit decreases during operation due to several reons: • Clogging of vacuum tubes and hoses attached to • Tip Extraction Accessories: Clean stainless steel vacuum tubes (1) periodically and frequently. Cleaning brushes are supplied with the iro h Line Callout 3 (No Border): 4 Line Callout 3 (No Border): 3 Line Callout 3 (No Border): 5 Line Callout 3 (No Border): 2 Line Callout 3 (No Border): 1 Line Callout 3 (No Border): 5 Line Callout 3 (No Border): 1 Line Callout 3 (No Border): 3 Line Callout 3 (No Border): 1 Line Callout 3 (No Border): 2 Line Callout 3 (No Border): 4 Line Callout 3 (No Border): 2 Line Callout 3: Air inlet cover with bypass valve Replacement of filters: If, after cleaning of accessories, the fumes are not extracted efficiently, replace filter(s) inside filter unit. Initially rep prefilter only. If th 1. Turn unit off. 2. Disconnect the power cord. 3. Unlatch the filter cove 4. Remove filter cover. Replace the filters. (Pre-filter/main filter). Make sureto place main filter inside the alignmen that interlock switch (3) is depressed. Replace filter cover and ensure proper fit on bottom 1 23 ousing. Hook both latches into filter cover and press down carefully. Caution! Do not use force. If filter cover on bottom housing. 7. Reconnect power cord and turn system on. N F T Problem Possibly C No Power Interlo Solution Check On/Off Switch Check power outlet Check powe Check filter Clogge hoses A Check safety interlock switch Clean extraction tube a Clean vacuum hoses Check duct connections for le T Max. number of statio 8 Flow rate per sio > 28 lit/min Noise Level: < 55 dBA Dimensions (Wx 508 x 254 x 38 Weight: 9 kg (20 lbs) Voltage 100-240 VAC Frequency 50 – 60 Hz Power 85 Watt C Part Num Replacementrs FM-BVX200 Main Duct ConnectiKits BTX-CK2-25 Hose connection kit 2-4 stations 2.5m (8’) long B BTX-CK4-75 Hose connection kit 2-4 stations 7.5m (25) long F Warranty OK International warrants the BTX-208 system against any defects in materials or workmanship for oyear from the date of purchase by the original owner. This Warranty excludes normal maintenance and shall not apply to any opened, misused, abused, altered or damaged items. If the product should become defective within the warranty period, OK International will repair or replace it free of charge at its sole oThe repaired or replacement item(s) will be shipped, freight pr p manufacture will be used as the start of the warranty period. F Contact Information North America OK International 12151 Monarch Street Garden Grove, CA 92841 USA Tel: +1 714-799-9910 Fax: +1 714-799-9533 France OK International SA Rue de la Saone Zac De Folliouses-Les Echets 01706 Miribel Cedex France Tel: +33 (0) 4 72 26 20 30 Fax: +33 (0) 4 72 26 20 35 Singapore OK International (Sales Support Office) 10 Ang Mo Kio St.65 #03-18/19 Techpoint Singapore 569059 Tel: +65-62810991 Fax: +65-62853473 United Kingdom OK International Ltd. Eagle Close, Chandlers Ford Hampshire, SO53 4NF U.K. Tel: +44 (0) 23 8048 9100 Fax: +44 (0) 23 8048 9109 Germany OK International GmbH Frankfurter Strasse 74 D-64521 Gross-Gerau Germany Tel: +49 (0) 61 52-71 12-0 Fax: +49 (0) 61 52-71 12-22 China OK Electronics (Beijing) Co., Ltd No. 1 Bldi, A-10 Long Qing Street Beijing Econ. & Tech. Developing Zone Beijing, ...