Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
• High-pressure hoses, fixtures and couplings are important for the safety of the appliance. Only use high-pressure hoses, fixtures and couplings recommended by the manufacturer. • This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities. The appliance must not be operated by children or persons who have not been instructed accordingly. Children should be supervised to prevent them from playing with the appliance. • The operator must use the appliance correctly. When working with the appliance, he must consider the local conditions and pay due care and attention to other persons, in particular children, who are nearby. • Do not use the appliance when there are other persons around unless they are also wearing safety equipment. • Wear protective clothing and safety goggles to protect against splash back containing water or dirt. English 5 Caution • Do not operate the appliance at temperatures below 0 °C. • Observe a distance of at least 30 cm when using the jet to clean painted surfaces to avoid damaging paintwork. • Never leave the appliance unattended when it is in operation. • Make sure that the power cable or extension cables are not damaged by running over, pinching, dragging or similar. Protect the power cable from heat, oil, and sharp edges. • All current-conducting parts in the working area must be protected against jet water. • The appliance may only be connected to an electrical supply which has been installed in accordance with IEC 60364. • The appliance may only be connected to alternating current. The voltage must correspond with the type plate on the appliance. • For safety reasons, we recommend that you operate the appliance only via a earth-leakage circuit breaker (max. 30 mA). • Cleaning operations which produce oily waste water, e.g. engine washes, underbody washes, may only be carried out using washing stations equipped with an oil separator. • This appliance was designed to be used with detergents which are supplied or recommended by the manufacturer. The use of other detergents or chemicals may compromise the safety of the appliance. Operation Before Startup Mount loose parts delivered with appliance prior to start-up. Illustrations on Page 10 Illustration • Pull out the clamp for the high-pressure hose from the trigger gun (e.g. a small screwdriver). Illustration • Connect high pressure hose to trigger gun. • Push the clamp in until it locks. Check the secure connection by pulling on the high-pressure hose. Illustration • Insert the transport wheels and lock them. Illustration • Attach rear cover. Illustration • Insert the transport handle. Illustration • Lock the detergent tank in place on the appliance. • Connect the suction hose for detergent to the connection. Illustrations - • Attach the accessories holder. Water supply According to the applicable regulations, the appliance must never be used on the drinking water supply without a system separator. Use a suitable system separator manufactured by KARCHER; or, as an alternative, a system separator as per EN 12729 Type BA. Water flowing through a system separator is considered non-drinkable. Note: Impurities in the water can damage the high-pressure pump and accessories. For protection, the use of the KARCHER water filter (optional accessory, order no. 4.730-059) is recommended. 6 English Water supply from mains Observe regulations of water supplier. For connection values, see type plate/technical data. • Use a fibre-reinforced water hose (not included) with a standard coupling. (Minimum diameter 1/2 inch (13 mm), minimum length 7.5 m). • Screw the coupling unit (supplied) to the water connection on the appliance. • Push the water supply hose onto the coupling unit, then connect it to the water supply. Start up Caution Dry runs lasting longer than two minutes lead to damages to the high pressure pump. If the appliance does not build up pressure within two minutes, switch it off and proceed as instructed in the Chapter "Help with faults". • Connect the high pressure hose to the high pressure connection of the appliance. • Push the spray lance into the trigger gun and fasten it by turning it through 90°. • Completely open the water tap. • Insert the mains plug into the socket. • Turn on the appliance “I/ON”. Operation . Danger The trigger gun is subjected to a recoil force when the water jet is discharged. Make sure that you have a firm footing and are also holding the trigger gun and spray lance firmly. • Unlock the lever on the trigger gun. • Pull on the lever of the trigger gun; the device will switch on. Note: Release the lever of the trigger gun; the device will switch off again. High pressure remains in the system. Spray lance with pressure regulation Carrying out the most common cleaning tasks. The work pressure can be stagelessly regulated between "Min" and "Max". • Release the lever on the trigger gun. • Turn the spray lance to the desired position. Spray lance with Dirtblaster For...