The grease filters should be cleaned straight away. Cleaning the metal-mesh grease filters: . The filters can be cleaned in a dishwasher. However, they may become slightly discoloured. Important: Do not wash highly saturated metalmesh grease filters with other utensils. . If cleaning the filters by hand, soak them in a hot soap solution. Then brush the filters, rinse thoroughly and leave to drain. Clean the support frame for the grease filters by hand. Filters and maintenance Filters and maintenance Activated carbon filter: For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Inserting the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. Insert the activated carbon filter. 3. Engage the catches at both sides. 4. Insert the metal-mesh grease filters (see ”Removing and inserting the metal-mesh grease filters”). 5. Cancel the a display. . Press the Lbutton for at least 3 seconds. The adisplay then goes out. Saturation indicator: When the activated carbon filter is saturated, an acoustic signal is emitted for 6 seconds when the fan has switched off and a is displayed. The activated carbon filter should then be replaced immediately. Removing the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal-mesh filters. 2. Depress the catches on both sides of the filter and remove the activated carbon filter. 3. Replacing the activated carbon filter: . A replacement filter can be obtained from any authorized dealer (see optional accessories). . Use original filters only. This will ensure maximum performance. 4. Insert the grease filters. Disposing of the old activated carbon filter: . Activated carbon filters do not contain any pollutants and can be disposed of with domestic refuse. Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. . When cleaning the grease filters, remove grease deposits from accessible parts of the housing. This prevents the risk of fire and ensures that the extractor hood continues operating at maximum efficiency. . Clean the extractor hood with a hot soap solution or a mild window cleaner. . Do not scrape off dried-on dirt but wipe off with a damp cloth. . Do not use scouring agents or abrasive sponges. . Note: Do not use alcohol (spirit) on plastic surfaces, as dull marks may appear. Caution: Ensure that the kitchen is adequately ventilated. Avoid naked flames! Clean the operating buttons with a mild soapy solution and a soft, damp cloth only. Do not use stainless-steel cleaner to clean the operating buttons. Stainless steel surfaces: . Use a mild non-abrasive stainless steel cleaner. . Clean the surface in the same direction as it has been ground and polished. Do not use any of the following to clean stainless steel surfaces: abrasive sponges, cleaning agents containing sand, soda, acid or chloride! Aluminium and plastic surfaces: . Use a soft, non-linting window cloth or micro-fibre cloth. . Do not use dry cloths. . Use a mild window cleaning agent. . Do not use aggressive, acidic or caustic cleaners. . Do not use abrasive agents. Replacing the light bulbs 1. Switch off the extractor hood and pull out the mains plug or switch off the electricity supply at the fuse box. When switched on, the halogen bulbs become very hot. Even for some time after the bulbs have been switched off there is still a risk of burns. 2. Remove the bulb ring with a screwdriver or similar tool. 3. Replace the halogen light bulb (conventional halogen bulb, 12 Volt, max. 20 Watt, G4 bulbholder). Caution: Plug-in bulbholder. Take hold of the bulb with a clean cloth. 4. Re-insert the bulb ring. 5. Restore the power by inserting the mains plug or switching on the fuse. Note: If the light does not function, check that the bulbs have been inserted ...

Ce manuel est également adapté pour les modèles :
Hoods - DHI965V/02 (4.84 mb)
Hoods - DHI965V/03 (4.84 mb)
Hoods - DHI965V/04 (4.84 mb)
Hoods - DHI965VGB/01 (4.84 mb)