Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: . When the grease filters reach saturation point, an acoustic signal is sounded for 6 seconds after the fan has switched off, and an . appears in the display. The grease filters should be cleaned straight away. Cleaning the metal grease filters: In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned one a month. The filters can be cleaned in a dish-washer. It is however possible that they will become slightly discoloured. The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. When cleaning the filters by hand, soak them in hot soapy water first of all. Do not use aggressive, acidic or caustic cleaners. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. Removing and inserting the metal grease filters: Only change the grease filter when the front panel is open. Please only pivot the pane to a maximum of 90° as the glass pane could otherwise be destroyed. 1. Press the catches on the front grease filters and fold down the grease filters max 90° 2. Press the catches on the rear grease filters and fold down the grease filters. 3. Clean the grease filter. 1 2 4. Insert the clean filters back into the hood. 5. Cancel the . in the display. Press the button 0. Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine! Clean the extractor hood with a hot soap solution or a mild window cleaner. Do not scrape off dried-on dirt but wipe off with a damp cloth. When cleaning the grease filters, remove grease deposits from accessible parts of the housing. This prevents the risk of fire and ensures that the extractor hood continues operating at maximum efficiency. Note: Do not use alcohol (spirit) on plastic surfaces, as dull marks may appear. Caution: Ensure that the kitchen is adequately ventilated. Avoid naked flames! Clean the operating buttons with a mild soapy solution and a soft, damp cloth only. Do not use stainless-steel cleaner to clean the operating buttons. Stainless steel surfaces: Use a mild non-abrasive stainless steel cleaner. Clean the surface in the same direction as it has been ground and polished. We recommend our stainless steel cleaner no. 461731. See enclosed service booklet for order address. Aluminium and plastic surfaces: Do not use dry cloths. Use a mild window cleaning agent. Do not use aggressive, acidic or caustic cleaners. en Replacing the light bulbs 1. Switch off the extractor hood and pull out the mains plug or switch off the electricity supply at the fuse box. 2. First remove the grease filter (see chapter Grease Filter and Maintenance) 3. Unscrew the grease filter frame by loosening the lens-head screws using the enclosed Allen key. Take particular care when loosening the last screw as the grease filter frame could fall down onto the hob. 4. Replace the defective illuminant (Osram Dulux S 11W) be carefully pulling it out of the holder. Please only use the hood with an illuminant inserted. 1 1 11 2 3 3 3 3 5. Now insert the filter frame again and tighten the 4 cheese-head screws using the Allen key. 6. Restore the power by inserting the mains plug or switching on the fuse. en If you encounter a problem Note: If the light does not function, check that the bulbs have been inserted correctly. If an . or [ appears in the display: See „Filters and maintenance“ Section. If is not possible to operate the extractor hood: Disconnect the extractor hood from the mains electricity supply by pulling out the plug or switching it off at the main fuse box. Wait for approx. 1 minute and then switch it on again. If you have any questions or if a fault occurs, please call Customer Service. (See list of Customer Service representatives). When you call, please quote the following: AB - Nr.: FD Enter the relevant numbers into the box above. The AB - Nr. (product no.) and FD (production date) are shown on the nameplate which can be seen inside the extractor hood after the filter frame has been detached. The manufacturer of the extractor hoods accepts no liability for complaints which can be attributed to the design and layout of the pipework. Installation Instructions: Important information Old appliances are not worthless rubbish. Valuable raw materials can be reclaimed by recycling old appliances. Before disposing of your old appliance, render it unusable. You received your new appliance in a protective shipping carton. All packaging materials are environmentally friendly and recyclable. Please contribute to a better environm...
Ce manuel est également adapté pour les modèles :Hoods - LC86K950/01 (2.89 mb)
Hoods - LC957KA70/01 (2.89 mb)
Hoods - LC957KB70/01 (2.89 mb)