Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
A separator must be installed in the household circuit. A suitable separator is a switch that has a contact gap of more than 3 mm and interrupts all poles. Such devices include circuit breakers and contactors. If the connecting cable for this appliance is damaged, the cable must be replaced by the manufacturer or his customer service or a similarly qualified person in order to prevent serious injury to the user. Electrical data: Are to be found on the name plate inside the appliance after removal of the filterframe. Before undertaking any repairs, always disconnect the extractor hood from the electricity supply. Length of the connecting cable: 1.30 m. This extractor hood corresponds to EC regulations concerning RF interference suppression. 27 Installation 05. Screw on the upper and the two lower fixing brackets. 24 300 mind 550 Elektro mind 650 Gas 233 471 112 Note: Take into account any special accessories that are going to be fitted. 06. Attach the extractor hood. Adjust the height and align horizontally with the adjusting screws. This extractor hood is intended to be mounted onto the kitchen wall. 01. Remove the grease filter (refer to Operating Instructions). 02. Draw a line on the wall from the ceiling to the lower edge of the hood at the centre of the location where the hood is going to be mounted. 03. Use the template to mark the points on the wall where the screws will be mounted. In order to make it easier to hook the hood onto the screws, draw the outline of the area where the hood will be attached. Ensure that the minimum distance between the hob and the extractor hood is maintained – 550 mm for an electric hob and 650 mm for a gas hob. The bottom edge of the template corresponds to the lower edge of the extractor hood (glass screen). 04. Drill 3 x l 8 mm holes for the extractor hood and 2 x l 8 mm holes for the chimney panelling. Insert plugs into the holes so that they are flush with the wall. 28 15. Insert the grease filter (refer to Operating Instructions). Installation 07. Screw in the lower bolt (hex bolt). 08. Connect up the air outlet pipe. 09. Connect the hood to the electricity supply. 10. Remove the protective film from the two flue ducts. Avoid damage to the sensitive surface. 12. Insert the upper flue duct (slots downwards) into the lower flue duct. Protect the cover panels from scratches, for example by laying the template used for marking the wall over the top edge of the lower section. 12. Insert the whole chimney cover panel inclined and press back. 13. Carefully pull the upper flue duct upwards and screw the sides to the fixing bracket with 2 screws. 14. Fitting the glass panel: – Hold the glass panel with both hands and carefully push it all the way to the bottom in the side guide rails. In doing so, do not scratch the printed area on the glass panel. – press the two plastic grommets, left and right into the fastening guide rails. In order to carry this out, the glass panel must be pushed all the way to the bottom. – fasten both screws, left and right into the plastic grommets. Mode d’emploi Description de l'appareil Bandeau en verre Capot de cheminee Commuta- teur Lumiere/ Ventilateur Eclairage Grille du filtre Modes de fonctionnement Air evacue a l'exterieur: . Le ventilateur de la hotte aspire les buees de cuisson qui traversent un filtre a graisse avant de regagner l'atmosphere exterieure. . Ce filtre retient les particules grasses solides en suspension dans les buees de cuisson. . Les particules grasses ne se deposent plus dans la cuisine, les odeurs de cuisson disparaissent. DSi la hotte evacue l'air a l'exterieur et si le logement comporte des moyens de chauffage (tels par ex. des appareils de chauffage au gaz, au fuel ou au charbon, chauffe-eau instantanes ou a accumulation) raccordes a une cheminee, veiller imperativement a ce que l'apport d'air soit suffisant pour assurer la marche du chauffage a combustion. Un fonctionnement sans risque est possible si la depression dans le local ou le foyer de chauffage est implante ne depasse pas 4...
Ce manuel est également adapté pour les modèles :Hoods - LC8K950GB/01 (8.53 mb)
Hoods - LC926KA40/01 (8.53 mb)
Hoods - LC956KA40/01 (8.53 mb)
Hoods - LC966KA40/01 (8.53 mb)