Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
The wall plugs must have a secure grip. ¦ The enclosed screws and wall plugs are suitable for solid brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks). ¦ The max. weight of the extractor hood is 40 kg. Electrical connection : Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter. Length of the cable: approx. 1.30 m This appliance complies with the EC interference suppression regulations. This appliance may be connected to a correctly installed earthed socket only. Attach the earthed socket preferably inside the flue duct. ¦ The earthed socket should be connected via its own circuit. ¦ If the earthed socket is no longer accessible following installation of the appliance, a disconnecter must be fitted as for a permanent connection. If a permanent connection is required, the installation must feature an all-pole disconnecter (circuit breakers, fuses and contactors) with a min. 3 mm contact opening. The permanent connection may be installed by an electrician only. Installation Preparing for installation Caution! Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made. 1.Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood. 2.Mark the positions for the screws and the contour of the attachment area. 3.Drill 8 mm O holes to a depth of 80 mm and press the wall plugs flush with the wall. . 4.Screw on the fixing bracket for the flue duct. © 5.Screw in 2 securing screws with washers to approx. 5 mm. . Installation 1. Attaching and aligning the appliance. . 2. Mark the hole for the safety screw. © 3. Remove the appliance once more. . Finishing installation of the appliance 1. Drill an 8 mm O hole to a depth of 80 mm for the safety screw and press the wall plug flush into the wall. . 2. Initially remove the protective foil from the back of the appliance and, following installation, remove the foil completely. 3. Attach the appliance. © 4. Screw in the safety screw -and washer -and tighten all the screws. . Connecting the appliance to the power supply Connecting the air extractor Note: If using an aluminium pipe, smooth the connection area beforehand. 1. Attach the air extractor pipe directly to the air-pipe connector. 2. Connect to air extractor opening. 3. Seal the joints appropriately. Connect the power supply 1. Plug the mains plug into the earthed socket. 2. If a fixed connection is required, please follow the instructions in the Electrical Connection section. Attaching the flue duct: Risk of injury! Components inside the appliance may have sharp edges. Wear protective gloves. 1. Separate the flue ducts. To do this, remove the adhesive tape 2. Remove the protective foil from both flue ducts. 3. Screw the upper flue ducts to the sides of the fixing bracket using two short screws. . 4. Place the lower flue ducts on the appliance and fix in place using two long screws on the bottom of the appliance. © 5. Screw the lower flue duct to the sides of the fixing bracket using 2 short screws. . Note: Align the flue duct before tightening the 2 screws. .Table des matieres NOTICE D'UTILISATION .......................................................... 22 Precautions de securite importantes ................................ 22 Protection de l'environnement ........................................... 24 Elimination sans nuisances pour l'environnement ............... 24 Modes ................................................................................... 24 Mode Evacuation de l’air........................................................... 24 Mode Recyclage de l’air............................................................ 24 Utilisation de l'appareil ....................................................... 25 Eclairage....................................................................................... 25 Nettoyage et entretien ......................................................... 25 Anomalies – que faire ? ...................................................... 26 Service apres-vente ............................................................ 27 Accessoires Mode recyclage ................................................... 27 NOTICE DE MONTAGE .............................................................28 Precautions de securite importantes .................................28 Consignes generales ...........................................................29 Mode Evacuation de l’air .......................................................... 29 Conduit d'evacuation ................................................................. 29 Verifier le mur ..............................................
Ce manuel est également adapté pour les modèles :Hoods - VVA92E350/01 (3.56 mb)