Log:
Évaluations - 2, GPA: 4 ( )

Instructions ColdTech, Modèle CFD-1F

Fabricant : ColdTech
Taille : 2.64 mb
Nom Fichier : 538a8c8c-1a53-4a26-96b3-60fb8a11872e.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


ColdTech recommends cleaning the condenser coil and fins at least once per month. Clean with a commercial condenser coil cleaner, available from any kitchen equipment retailer. Brush the condenser fins from top to bottom, not side to side. After cleaning, straighten any bent condenser fins with a fin comb. CLEANING THE FAN BLADES AND MOTOR If necessary, clean the fan blades and motor with a soft cloth. If it is necessary to wash the fan blades, cover the fan motor to prevent moisture damage. CLEANING THE INTERIOR OF UNIT When cleaning the cabinet interior, use a solvent of warm water and mild soap. Do not use steel wool, caustic soap, abrasive cleaners, or bleach that may damage the stainless steel surface. Wash door gaskets on a regular basis, preferably weekly. Simply remove door gasket from the frame of the door, soak in warm water and soap for thirty (30) minutes, dry with soft cloth, and replace. Check door gaskets for proper seal after they are replaced. Periodically remove the shelves and pilasters from the unit and clean them with mild soap and warm water. To remove the pilasters, first remove the shelves and shelf brackets. Then, simply lift the pilaster up and out. WARNING Disconnect power cord before cleaning any parts of the unit. TROUBLE SHOOTING Before requesting any service on your ColdTech unit, please check the following points. Service calls resulting from lack of maintenance or misuse is not covered under warranty and also may void warranty. Please note that this guide serves only as a reference for solutions to common problems. -6 SEEPAGE9 SEEPAGE9 -7 -8 Applicable to Models: CFD-1R, CFD-2R, CFD-3R ColdTech® Refrigerator Settings Temperature set to 37 F Parameter Function Set Range Default E1 Lower Setpoint Limit -40 F ~ set temp 36 F E2 Higher Setpoint Limit set temp ~ 120 F 45 F E3 Hysteresis, temp. variance 1 ~ 18 F 10 F E4 Comp. start delay time 0 ~ 10 min. 2 min. E5 Offsetonroomtemp -5~5F 0F E6 Offsetonevaptemp -5~5F 0F F1 Max. defrost duration 1 ~ 60 min. N/A F2 Defrost interval time 0 ~ 24 hr. 0 F3 Defrost termination temp 32 ~ 68 F N/A Key F = Farenheit (degrees) temp = temperature min. = minutes max = maximum hr. = hours N/A = not applicable Warning: Do not change the default settings of your ColdTech unit without consulting a qualified service technician or theColdTech service department. -9 Applicable to Models: CFD-1F, CFD-2F, CFD-3F ColdTech® Freezer Settings Temperature set to -4 F Parameter Function Set Range Default E1 Lower Setpoint Limit -40 F ~ set temp -10 F E2 Higher Setpoint Limit set temp ~ 120 F 20 F E3 Hysteresis, temp variance 1 ~ 18 F 10 F E4 Comp. start delay time 0 ~ 10 min. 3 min. E5 Offsetonroomtemp -5~5F 0F E6 Offsetonevaptemp -5~5F 0F F1 Max. defrost duration 1 ~ 60 min. 30 min. F2 Defrost interval time 0 ~ 24 hr. 6 hr. F3 Defrost termination temp 32 ~ 68 F 68 F Key F = Farenheit (degrees) temp = temperature min. = minutes max = maximum hr. = hours N/A = not applicable Warning: Do not change th...

Ce manuel est également adapté pour les modèles :
Réfrigérateurs - CFD-2F (2.64 mb)
Réfrigérateurs - CFD-2R (2.64 mb)
Réfrigérateurs - CFD-3F (2.64 mb)
Réfrigérateurs - CFD-3R (2.64 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories