Log:
Évaluations - 4, GPA: 4.5 ( )

Instructions Apex Digital, Modèle External Charger

Fabricant : Apex Digital
Taille : 268.87 kb
Nom Fichier : 6d666086-a57b-4754-a118-897cdd57a3ed.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


• DO NOT tamper or operate the Apex III External Charger if the case is perforated, broken, or loosely held together. • DO NOT operate the Apex III External Charger in any outside location where it could become exposed to the elements. The Apex III External Charger has been designed for indoor use only. • DO NOT attempt to charge any other type battery pack or batteries other than Apex III Battery Packs with your Apex III Dock or Apex III External Charger. • ONLY use Compsee, Inc. approved cables and Power Supplies with your Apex III products. • DO NOT touch more than one Battery Pack terminal at a time with any electrically conductive material. A short across the Battery Pack terminals could result in the sudden release of a large portion of the Battery Pack’s energy. Unpacking And Initial Setup 1. Remove the Apex III External Charger from the packing carton and inspect the unit to ensure it is good physical condition after shipping. Charge State LED Indicating Light [One Per Side] Figure 1: Apex III External Charger 2. If you have ordered an External Charger Kit (Kit 1 or 2 – refer to the Support Section of the External Charger User’s manual for part numbers and description), remove the associated Power Supply and AC Line cable (if applicable) from the packing container (refer to Figure 2 and Figure 3). Figure 2: External Charger Power Supply COAM30006 Rev. 1.02 11/22/00 Apex III External Charger Quick Start Guide Figure 3: AC Line Cord (120 VAC Cord Shown) 3. Record the Unit Specific Information (External Charger and Power Supply Model and Serial numbers) in a location you will remember for future reference before permanently installing your Apex III External Charger. 4. Plug the female end of your AC Line cord into the Power supply connector (refer to Figure 4). Power Supply AC Line Plug [Power Supply Side] AC Connection Figure 4: Power Supply AC Power Connection 5. Plug the round male Power Supply DC voltage connector (cable permanently attached to Power Supply) into the DC voltage connector on the back of the Apex III External Charger (refer to Figure 5). External Charger Back DC Power Connector Power Supply DC Voltage Connector Voltage Key 9VDC 3.5A Figure 5: Apex III External Charger (Rear View) 6. Plug the AC Line cord into an AC power receptacle (refer to Figure 6). AC Power Cord AC Receptacle Figure 6: AC Power Connection 7. Insert one or two Apex III Battery Pack(s) into the charging slot(s) on the top of the Apex III External Charger (refer to Figure 7 and accompanying Note). COAM30006 Rev. 1.02 11/22/00 Apex III External Charger Quick Start Guide Note: Battery Pack must be placed in the charging slot with Release Clip facing upwards and the four side charging terminals (and ridges) facing outward towards the side of the unit. This orientation applies to the insertion of both Battery Packs (one Battery Pack will be turned the opposite of the other). Charging Terminals Battery Pack Release Clip Figure 7: Battery Pack Orientation External Charger Operation Note: The Apex III External Charger is equipped with a quick charge circuit allowing an Apex III Battery Pack to be fully charged from a full discharge condition within 2 hours. Battery Pack Charging 1. To charge an exhausted Apex III Battery Pack, place the Battery Pack into the External Charger charging slot as described in the Unpacking And Initial Setup section. 2. Once an Apex III Battery Pack has been inserted into the External Charger charging slot per the previous instructions, the charging process will commence immediately and be controlled automatically by the unit. No additional action is required by the user, except for Battery Pack removal once the Battery Pack has been fully charged. 3. Upon initial insertion of a Battery Pack into the unit, the respective side LED indicator light on the front of the unit will flash Red. After a short period of time (no longer than 15 minutes) the LED will solidly illuminate Red to indicate that the Battery Pack is being charged in the fast mode. 4. When the Apex III External Charger senses that the Battery Pack charge state has reached approximately 92% charge, the respective side LED indicator light on the front of the unit will change to solid Green informing the user that the unit is charging the Battery Pack in the trickle mode. The trickle charging mode will continue until the Battery Pack is removed from the charging slot. COAM30006 Rev. 1.02 11/22/00 Apex III External Charger Quick Start Guide Note: Apex III Battery Packs use Nickel Metal Hydride (NiMH) composition, they DO NOT succumb to memory (hysteresis) loss as do Nickel Cadmium (Ni-Cd) batteries. Apex III Battery Packs can therefore be charged while in any state-ofcharge and DO NOT require full discharge prior to charging; however, it is still recommended that the Battery Pack be fully discharged periodically to reset the internal gas gauge circuitry. 5. If your Apex III Portable Data Collection Terminal (PDT) is ready for another Ba...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories