Évaluations - 4, GPA: 3.8 ( )

Fabricant : Philips Taille : 2.49 mb Nom Fichier : hx6911_02_dfu_nld.pdf Langue d'enseignement:

Smartimer The Smartimer indicates that your brushing cycle is complete by automatically switching off the toothbrush at the end of the brushing cycle. Dental professionals recommend brushing no less than 2 minutes twice a day. -- - - 1 2 ENGLISH 9 1243 Quadpacer -The Quadpacer is an interval timer that has a short beep and pause to remind you to brush the 4 sections of your mouth. Depending on the brushing mode or brushing routine you have selected, the Quadpacer beeps at different intervals during the brushing cycle. See the ‘Brushing instructions’ and ‘Personalising your brushing experience’ sections. The Quadpacer on this model has been activated.To deactivate or reactivate the Quadpacer: 1 2 Place the handle with a brush head attached on the plugged-in charger or sanitiser To deactivate the Quadpacer: press and hold the Personalised Brushing button for 5 seconds.You hear 1 beep to indicate that the Quadpacer has been deactivated. To reactivate the Quadpacer: press and hold the Personalised , Brushing button for 5 seconds until you hear 2 beeps.This indicates that the Quadpacer is active again. Note:The Quadpacer cannot be deactivated on the pre-programmed Go Care and Max Care brushing routines. Cord wrap on deluxe charger (specifi c types only) If your model includes the deluxe charger cover and base, the travel charger is pre-installed inside the cover. If you want to shorten the mains cord, you can store excess cord in the cord-wrap feature built into the charger base. 1 To separate the charger cover from the charger base, press the two grey snap bars on the charger base and pull the white charger cover upwards. 2 Wrap excess cord around the grey charger base as shown in the picture. Be sure to wrap the cord on the inside of the two snap levers. 3 4 When you have stored the excess cord, guide the cord through the small groove in the rear of the grey charger base. Reattach the charger cover by pressing it down over the charger base until it snaps into place. Tip: For extra convenience during travel, you can remove the travel charger and use it without the charger cover and charger base. 10 ENGLISH Cord wrap on sanitiser (specific types only) If your model includes the sanitiser, you can store excess cord with the cord-wrap feature built into the bottom of the sanitiser. Sanitising (specific types only) - -With the sanitiser, you can clean your brush head after every use. Discontinue use of the sanitiser if the UV light bulb remains on when the door is open or if the Philips logo is broken or missing from the sanitiser. UV light can be harmful to the human eye and skin. Keep the sanitiser out of the reach of children at all times. Unplug the sanitiser and call Customer Service if the sanitiser gives off smoke or a burning smell while it is operating. 1 After brushing, rinse the brush head and shake off excess water. Do not place the travel cap on the brush head during sanitisation. 2 To open the sanitiser door, press the door release button. 3 Place the brush head on one of the 2 pegs in the sanitiser. -Make sure the bristles of the brush head directly face the light bulb. Note: Only clean Sonicare ProResults brush heads in the sanitiser. 4 Make sure the sanitiser is plugged into wall socket. 5 Close the door and press the green power on/off button once to select the UV clean cycle. Note:You can only switch on the sanitiser when the door is properly closed. Note: If you open the door during the sanitising cycle, the sanitiser stops. Note:The sanitiser cycle runs for 10 minutes and then automatically switches off. The sanitiser is in operation when the blue light glows through the , Philips logo and the UV clean LED fl ashes slowly. When the sanitising cycle is complete, the UV clean LED lights up , green continuously and the sanitiser automatically switches off. ENGLISH 11 Cleaning Do not clean brush heads, the handle, the travel charger, the charger cover and the UV sanitiser in the dishwasher. Toothbrush handle 1 Remove the brush head and rinse the metal shaft with warm water. Do not push on the rubber seal round the metal shaft with sharp objects, as this may cause damage. 2 Use a damp cloth to wipe the entire surface of the handle. Brush head 1 Rinse the brush head and bristles after each use. 2 Remove the brush head from the handle and rinse the brush head connection at least once a week with warm water. Travel charger and deluxe charger (specifi c types only) 1 Unplug the charger. 2 Specific types only: Disassemble the deluxe charger and take out the travel charger. 3 Use a damp cloth to wipe the surface of the charger. Sanitiser (specific types only) Do not clean the sanitiser when the UV light bulb is hot. For optimal effectiveness, it is recommended to clean the sanitiser weekly. 1 Unplug the sanitiser. 2 Slightly lift the drip tray and pull it out. Rinse the drip tray and wipe it clean with a damp cloth. 3 Clean all reflector surfaces with a damp cloth. 12 ENGLISH Storage Replacement Disposal ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :