2. Insert Telescoping Legs into Receptors with spring clips inside legs. Important: Orient legs so small tube welded to leg faces inward. This will ensure proper fit of the Wire Brace. Legs extend by pushing in on both spring clips protruding from the legs and pulling the legs outward. Then lock leg in place by aligning spring clips with holes in legs. Always be sure spring clip is protruding through holes in legs to ensure stability. Small tubes must face inward Spring Clip Telescoping Leg Rece
& foreign patents pending Fireplace/Charcoal Grill Model 5065-715 Introduction Your Coleman® RoadTrip® Fireplace/Grill is a versatile unit that functions as either a fireplace or a charcoal grill. Follow these instructions for assembly and read carefully, particularly the safety statements. The safety alert symbol, is a universally recognized symbol used to identify safety information about hazards that can result in personal injury. When this symbol is used you should pay very close attention t
Proof of gas seal between the connector and the cylinder before gas flow takes place. 2. A flow-limiting device designed to limit the flow of gas in the event of a regulator or hose failure. 3. The connection has a thermal shut-off which will stop the flow of gas if the connection reaches a certain temperature. CURRENT GAS CYLINDERS ARE ALSO EQUIPPED WITH AN OVERFILL PROTECTION DEVICE (O.P.D.) WHICH GREATLY REDUCES THE CHANCE OF ACCIDENTALLY OVERFILLING THE CYLINDER. SPECIAL NOTE CONCERNING L.P.
• Also try placing a pan of water above the lit burner side to help meat retain its juices. Replenish water as needed. 29 Cleaning the Venturi WARNING Spider’s nests or wasp’s mud inside the venturi may cause fire at valve. If a fire occurs, immediately turn off gas supply at L.P. cylinder valve (see representative illustration in Fig. 22). If your grill is set up for use with Natural Gas, turn off gas supply at the system manual shut off valve. Note: Spiders and small insects can spin webs and
4-B 4-B. Assemble one Door Magnet to the Base with two Screws (TN). Door Magnet TN (x2) Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty. 11 .... Assemble two Spacers to the Top Panel. .... Assemble the Top Panel to the Grill Cart. 5-A 5-A. Assemble the two Spacers to the Top Panel with four Screws (TN). Hardware shown actual size TN (x4) Top Panel Step 5 (TN) M6 x 15mm Screw (11) Qty. Spacer (x2) (with flange up) 5-B 5-B. Assemble the Top Panel to the Grill Cart with seven Screws (TN). T
19-C Quick Disconnect Coupling 27ATTACHED TO THE FUEL SOURCE. WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three- quarters additional turn to complete the connection. To disconn
Gas industry procedures. Failure to follow this instruction may result in explosion, fire, serious personal injury, or death. A. Hose end valve with a bleed port (Fig. 13): Purging can be accomplished using a hose end valve containing a bleed port which also allows for evacuation without the use of an adapter. B. Hose end valve without a bleed port: When a hose end valve does not have a bleed port, a separate device must be used for evacuation. C. Purging using a Type 1 connection (Fig. 14): L.P
IMPORTANT Read this manual carefully before assembling, using or servicing these stoves. Keep this manual for future reference. If you have ques ® tions about assembly, operation, servicing or repair of these please call Coleman at 1-800-835-TDD: 316-832-8707. Model 5428A In Canada CERTIFIED ANS Z21.72b- Contents Contents DANGER General Safety Information To Set Up To Light To Turn Off To Clean To Store Things You Should Know Parts List Warranty General Safety Information FOR YOUR SAFETY If you
Do not bend the hooks while inserting or removing the Fryer Grease Pan. Fryer Grease Pan Hooks 19Electrode Wire Fryer Panel Step15 • ....Assemble Front Fryer Heat Shield. 15-A Fryer Heat Shield Engage Tabs into Rectangle Holes Electrode Wire 15-A. Assemble Fryer Heat Shield. • ....NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. • ....Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B Fryer Heat Shield
Outdoor Use Only I IIM MMP PPO OOR RRT TTA AAN NNT TT Read this manual carefully before assembling, using or servicing this grill. Keep this manual for future reference. If you have questions about assembly, operation, servicing or repair of this grill, please call Coleman at 1-800-835-3278 or ®® TDD: 316-832-8707. In Canada call CERTIFIED 1-800-387-6161. Contents General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Installation . .