& foreign patents pending Fireplace/Charcoal Grill Model 5065-715 Introduction Your Coleman® RoadTrip® Fireplace/Grill is a versatile unit that functions as either a fireplace or a charcoal grill. Follow these instructions for assembly and read carefully, particularly the safety statements. The safety alert symbol, is a universally recognized symbol used to identify safety information about hazards that can result in personal injury. When this symbol is used you should pay very close attention t

Wear a barbecue mitt and scrub the cooking grate with a damp cloth. If the grill is allowed to cool down, cleaning the grate will be easier if removed from the grill and cleaned with a mild detergent. Note: Allow the drip tray to cool before attempting to clean. Important: Do not leave the grill outside during inclement weather unless it is covered (cover sold separately). Rain water can collect inside of the grill, or in the drip tray if left uncovered. If the drip tray is not cleaned after use

16). 20. Reattach the control knobs onto the manifold stems, making sure the arrow is facing upwards (See Fig. 11 on previous page). 21. Reinstall burners into the grill body. Line up the Fig 17 burners with the valves on the manifold, making sure they are level (Fig. 17 & 18). 22. Reattach the electrode and their heat shields to the burners (Fig. 2, 3, and 4). 23. Reattach the rear heat shield before attaching the front heat shield to be sure the burners remain over the valves (Fig. 19). Fig 18

Screw on the outer threaded sleeve in a clockwise direction until tight. Step 4 ¦ Never operate stove with propane cylinder in an inverted position. Leak Check 5 Setup with Hose* and Refillable Cylinder *(sold seperately) • Read and follow all instructions and warnings provided with your appliance. • Do not store LP gas cylinders under or near this appliance. • Never fill the cylinder beyond 80% full. • Failure to follow the above instructions exactly may result in fire causing death or serious

33-B Set Collar Slip Collar Center Firebox Wall Small Gap here 33-B. Insert the Spit Rod into the Motor. Make sure the machined groove is toward the handle. • ....Place Slip Collar on Firebox Wall. Make sure the pointed tip of the Spit Rod stays in the Motor. • ....Push Set Collar against the Slip Collar, provide a small gap to allow the Spit Rod to freely turn. • ....Tighten the thumbscrews on the Set Collar and the Forks to hold in place. 3233-A Handle Set Collar Fork(x4) Long Spit Rod NOTE: M

Tighten connections with an adjustable wrench and replace damaged parts. Perform a leak test on all connections before cooking on grill again. 3. Venturi may be misaligned and needs to be lined up over orifice. DANGER If a fire occurs at the cylinder valve, DO NOT attempt to move the cylinder. IMMEDIATELY call the fire department and clear the area. You can safely spray water with a garden hose from a distance of at least 15 feet away from cylinder until firemen arrive. For Your Additional Safet

Hardware to attach the thermometer are two wing nuts. Finger tighten the wing nuts on the inside of the lid. DO NOT OVERTIGHTEN the wing nuts (Fig. 24 and 25). Fig. 24 Fig. 25 Assemble the Warming Rack and the Grease Tray Assemble the Propane Tank Retainer 1. Insert the ends of the Propane Tank Retainer into the holes provided in the right side panel (Fig. 29). Use the pins provided with the Retainer to secure the Retainer in place. Fig. 29 Assemble the Wire Shelf 1. Insert the ends of the Wire

• Also try placing a pan of water above the lit burner side to help meat retain its juices. Replenish water as needed. 29 Cleaning the Venturi WARNING Spider’s nests or wasp’s mud inside the venturi may cause fire at valve. If a fire occurs, immediately turn off gas supply at L.P. cylinder valve (see representative illustration in Fig. 22). If your grill is set up for use with Natural Gas, turn off gas supply at the system manual shut off valve. Note: Spiders and small insects can spin webs and

2. Insert Telescoping Legs into Receptors with spring clips inside legs. Important: Orient legs so small tube welded to leg faces inward. This will ensure proper fit of the Wire Brace. Legs extend by pushing in on both spring clips protruding from the legs and pulling the legs outward. Then lock leg in place by aligning spring clips with holes in legs. Always be sure spring clip is protruding through holes in legs to ensure stability. Small tubes must face inward Spring Clip Telescoping Leg Rece

INSTALLATEUR : Laissez ces instructions a l'utilisateur. CONSOMMATEUR/UTILISATEUR : Lisez toutes ces instructions et conservez-les dans un lieu sur pourtoute reference ulterieure. MONTADOR/INSTALADOR: Deje estas instrucciones con el consumidor. CONSUMIDOR/USUARIO: Lea todas estas instrucciones y mantengalas en un lugar seguro como referencia. 3600 N. Hydraulic Wichita, KS 67219 Internet site: 1-800-356-3612 TDD: 316-832-8707 G000A001 (03/25/02) E n g l i s h F r a n c a i s E s p a n o WARNING!