Évaluations - 5, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Panasonic, com). □ Monaural connection cable (RJL1P015B50)........................Ipc. □ AC power supply cord (RJA0065-K).....................................1 pc. man The included AC power supply cord is for use with this unii only. Do not use it with other equipment. □ Speaker feet (RFA0631A-K)................................1 sheet {4 feet) Replacements sold in 1-sheet lots (4 feet per sheet). Teclmicsf Active subwoofer system Operating Instructions Model No. SB-AS100 ■ SPEAKER SECTION Type 1 way 2 speaker system Bass-reflex type Speaker Woofer 14 cm{5-1/2v) cone type * 2 Impedance 1 il Input power Music 200 W DIN 100 w Sound pressure level 82 dB/W (1.0 m) Frequency range 40-380 Hz (at -16 dB) 45-310 Hz (at -10 dB) ■ AMPLIFIER SECTION Continuous power output 2Q-200 Hz (THD 1%) 100 W(1 il) Phase switching NORMAL'REVERSE Input sensitivity/impedance 335 mV/15 kii Low pass filter 50-200 Hz Variable ■ GENERAL Power supply AC 120 V. 60 Hz Power consumption 40 W Dimensions (W * H * D) (231 * 450X350) mm (9-3/32" X 17-23/32" x 13-25/32") Mass 9.0 kg(19.8 lb.) Specifications are subject to change without notice. Mass and dimensions are approximate Product service Do not attempt to remove the cover(s) or repair the unit yourself. Refer servicing to qualified personnel only. Product information For product service, product information or assistance with prod- uct operation, refer to the servicenter directory. For detailed instructions, contact an authorized servicenter In the U.S.A. and Panasonic Canada Inc. Customer Care Cen- tre In Canada. In the U.S. A.1-800-211-7262 or web site ( In Canada 905-624-5505 or web site (ca) RQT5460-P □ Center speaker Surround speakers (not included) TV (not included) (not included) SB-AS100 Monaural connection cable (included) /-o=- ■3oqf=l y ooooo ooooo (COCO (COCO Receiver (or amplifier) (not included) Household AC outlet (AC 120V/60Hz) AC power supply cord (included) Positioning the speaker_ □ Attach the rubber feet (included) to the speaker Attach these rubber feet to prevent vibration causing the speaker to move or fall over. 0 The diagram shows the basic positioning of each speaker. • The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV. • Do not place any object on top of this unit. If irregular coloring occurs on your television this speaker is designed to be used close to a television, but the picture may be affected with some televisions and set-up combinations. If this occurs, turn the television off for about 30 minutes. The television’s demagnetizing function should correct the problem. If it persists, move the speaker further away from the television. Note: Do not attach this speaker to walls or ceilings. Protection circuitry This unit incorporates speaker-protection circuits to prevent damage caused by excessive input or abnormal signals. When excess input Is detected, the input is automatically interrupted. ■ If sound is interrupted... 1. Reduce the volume level from the receiver or amplifier. 2. Check whether or not there is anything wrong with the equipment used such as the sound source, or connections. If there is nothing wrong, turn off the power. 3. Turn on the power once again. ■ After the protection circuitry is reset... Take care not to increase the receiver's or amplifier's volume level too much. Other notes: Be sure to reduce the volume on the receiver (or amplifier) when the signal input exceeds the rated allowable input to avoid damage to circuitry or other malfunctions. O Connections Connecting to receiver (or amplifier) Note: • Can be connected to a receiver (or amplifier) with a pin cord type subwoofer terminal. • Before making the connections, switch OFF the power to the receiver (or amplifier). Power connections Connect AC power supply cord after all other cables and cords are connected. Note 1. Avoid placing in areas as follows: • In direct sunlight • Near heating appliances or other sources of heat • Where there is high humidity 2. Never use alcohol, paint thinner, benzine or similar chemicals to clean the unit, as they may damage the finish. 1 POWER -J». »OFF CM BOv~v1D° LOW PASS 60 O ,5° filter 50 200 H2 CO VOLUME MIN MAX 4 1 eJPHASE *NORUAl Frequency response by LOW PASS FILTER setting Frequency response by VOLUME setting I Operation_ Set the low pass filter, volume and phase to suit characteristics of the speaker and SB-AS100 combination. 1 Set [POWER] to the “ ON” position. The unit is now in standby mode and the POWER indicator turns red. When a signal is received the unit turns ON automatically and the indicator turns green. The unit automatically switches to standby if a signal is not received for approximately two (2) minutes 2 Set [LOW PASS FILTER] to a suitable frequency. Refer to “Frequency response by LOW PASS F...