Évaluations - 2, GPA: 3
(
)
)
|
Photos et spécifications Bowers & Wilkins 703 |
Facilité d'utilisation
This can improve the resolution of low-level detail. Observe the correct polarity as before. When bi-wiring, incorrect connection can also impair the frequency response. The terminals accept 6mm (1/4-in) spades, bared wire ends or round pins up to 6mm diameter and 4mm banana plugs. When using spades, fit them under the sliding collar. Important safety notice: In certain countries, notably those in Europe, the use of 4mm banana plugs is considered a potential safety hazard, because they may be inserted into the holes of unshuttered mains supply sockets. In order to comply with European CENELEC safety regulations, the 4mm holes in the ends of the terminals are blocked by plastic pins. Do not remove the pins if you are using the product where these conditions apply. Always screw the terminal caps down tightly to optimise the connection and prevent rattles. Ask your dealer for advice when choosing cable. Keep the total impedance below the maximum recommended in specification and use a low inductance cable to avoid attenuation of the highest frequencies. Positioning (Figure 4) Some experimentation with the position of the speakers is well worthwhile to optimise the interaction between them and the listening room. However, as an initial guide: • Do not fit the spike feet until you have found the best position for the speakers. • Place the speakers and the centre of the listening area approximately at the corners of an equilateral triangle. • Keep the speakers at least 1.5m (5ft) apart to maintain left-right stereo separation. • Keep the speaker baffles at least 0.5m (20in) clear of walls. Having the speakers too close to walls increases the level of bass relative to midrange and may give a boomy quality to the sound. Stray magnetic fields The speaker drive units create stray magnetic fields that extend beyond the boundaries of the cabinet. We recommend you keep magnetically sensitive articles (television and computer screens, computer discs, audio and video tapes, swipe cards and the like) at least 0.5m from the speaker. Fine tuning Before fine tuning, make sure that all the connections in the installation are correct and secure. If the level bass is uneven with frequency it is usually due to the excitation of resonance modes in the room. Even small changes in the position of the speakers or the listeners can have a profound effect on how these resonances affect the sound. Try mounting the speakers along a different wall. Even large pieces of furniture can have an effect. Moving the speakers further from the walls will reduce the general level of bass. Space behind the speakers also helps to create an impression of depth. Conversely, moving the speakers closer to the walls will increase the level of bass. If you want to reduce the bass level without moving the speakers further from the wall, fit the foam bungs in the port tubes. (Figure 6) If the central image is poor, try moving the speakers closer together or toeing them in so they point just in front of the listeners. (Figure 5) If the sound is too harsh, increase the amount of soft furnishings in the room (for example use heavier curtains), or reduce it if the sound is dull and lifeless. Test for flutter echoes by clapping your hands and listening for rapid repetitions. Reduce them by the use of irregular shaped surfaces such as bookshelves and large pieces of furniture. Ensure the speakers stand firmly on the floor. Whenever possible fit the spike feet supplied after you have optimised the positioning. These are designed to pierce through carpets to the floor surface. Initially, screw the lock nuts fully onto the spikes and screw the spikes fully into the threaded inserts in the base of the cabinet. If the cabinet rocks, unscrew the two spikes that do not touch the floor equally until the cabinet sits firmly on the floor, and lock the nuts against the cabinet. If the unit is to be placed on a vulnerable surface, such as a wooden floor, either place a protective disc under each spike or fit the four rubber feet in place of the spikes. Check that there are no cables under the carpet that may be damaged by the spike feet. Do not walk the product on the spike feet as this may cause them to become detached from the cabinet and cause damage. Take care not to impale yourself with the spike feet when moving the product. Running-in period The performance of the speaker will change subtly during the initial listening period. If the speaker has been stored in a cold environment, the damping compounds and suspension materials of the drive units will take some time to recover their correct mechanical properties. The drive unit suspensions will also loosen up during the first hours of use. The time taken for the speaker to achieve its intended performance will vary depending on previous storage conditions and how it is used. As a guide, allow up to a week for the temperature effects to stabilise and 15 hours of average use for the mechanical parts to attain their intended...
Ce manuel est également adapté pour les modèles :Haut-parleurs - 704 (3.56 mb)