Log:
Évaluations - 2, GPA: 4 ( )

Instructions Sony, Modèle CDX-L450

Fabricant : Sony
Taille : 1.7 mb
Nom Fichier : Sony-CDX-L450-Pdf-Rus.Pdf
Langue d'enseignement: rusvenesetptfica
Photos et spécifications   Sony  CDX-L450
Aller à la télécharger



Par ce dispositif a également d'autres instructions :
Unité - CDX-L450 (165.99 kb)de
Unité - CDX-L450 (255.81 kb)en
Unité - CDX-L450 (1.34 mb)nl

Facilité d'utilisation


Ill V D-BASS Turn ■ ru The current programme type name appears if the station is transmitting the PTY data. “-----” appears if the received station is not an RDS station, or if the RDS data has not been received. Press (prst) repeatedly until the desired programme type appears. The programme types appear in the order shown in the above table. Note that you cannot select “NONE” (Not specified) for searching. C) pjLj V D-BASS 5PDRT Press (ENTER). The unit starts searching for a station broadcasting the selected programme type. Not specified NONE 2 3 Note You cannot use this function in some countries where no PTY (Programme Type selection) data is available. 16 Setting the clock automatically The CT (Clock Time) data from the RDS transmission sets the clock automatically. 1 During radio reception, press (menu), then press either side of (prst) repeatedly until "CT" appears. 5ET \D-BASS CT-OFF 2 Press the (+) side of (seek/ams) repeatedly until "CT-ON" appears. The clock is set. 5ET \D-BASS FT- ON 3 Press (enter) to return to the normal display. To cancel the CT function Select "CT-OFF" in step 2. Notes • The CT function may not work even though an RDS station is being received. • There might be a difference between the time set by the CT function and the actual time. Other Functions You can also control the unit with a rotary commander. Labelling the rotary commander (optional) Depending on how you mount the rotary commander, attach the appropriate label as shown in the illustration below. 17 Using the rotary commander (optional) The rotary commander works by pressing buttons and/or rotating controls. By pressing buttons (the SOURCE and MODE buttons) Each time you press (source), the source changes as follows: Tuner t CD Pressing (mode) changes the operation in the following ways: • Tuner: FM1 t FM2 t FM3 t MW t LW By rotating the control (the SEEK/AMS control) Rotate the control momentarily and release it to: • Locate a specific track on a disc. Rotate and hold the control until you locate the specific point in a track, then release it to start playback. • Tune in stations automatically. Rotate and hold the control to find a specific station. By pushing in and rotating the control (the PRESET/DISC control) Push in and rotate the control to: • Receive the stations memorised on the number buttons. • Change the disc. 18 Other operations Rotate the VOL control to adjust the volume. Press (att) to attenuate the sound. Press (off) to turn off the unit. Press (sound) to adjust the volume and sound menu. Press (dspl) to display the memorised names. Tip If your car has no ACC (accessory) position on the ignition key switch, be sure to press (off) for two seconds to turn off the clock indication after turning off the engine. Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. You can store the bass and treble levels independently for each source. 1 Select the item you want to adjust by pressing (sound) repeatedly. Each time you press (SOUND), the item changes as follows: BAS (bass) t TRE (treble) t BAL (left-right) t fAd (front-rear) 2 Adjust the selected item by pressing either side of (seek/ams). When adjusting with the rotary commander, press (SOUND) and rotate the VOL control. Note Adjust within three seconds after selecting the item. Changing the operative direction The operative direction of controls is factory-set as shown below. To increase To decrease If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. Press (sound) for two seconds while pushing the VOL control. Tip You can also change the operative direction of these controls with the unit (see "Changing the sound and display settings " on page 20). Attenuating the sound (with the rotary commander-optional) Press (att) on the rotary commander. “ATT-ON” flashes momentarily. To restore the previous volume level, press (ATT) again. Tip When the interface cable of a car telephone is connected to the ATT lead, the unit decreases the volume automatically when a telephone call comes in (Telephone ATT function). 1 Press (MENU). 2 Press either side of (prst) repeatedly until the desired item appears. Each time you press the (-) side of (PRST), the item changes as follows: CLOCK t CT t BEEP t RM t AMBER/GREEN t D.INFO t M.DSPL t A.SCRL* * When no CD TEXT disc is playing, this item will not appear. Note The displayed item will differ depending on the source. Changing the sound and display settings The following items can be set: ^ SET (setting) • CLOCK (page 7) • CT (Clock Time) (page 17) • BEEP — to turn the beeps on or off. • RM (Rotary Commander) — to change the operative direction of the controls of the rotary commander. — Select “NORM” to use the rotary commamder as the factory-set position. — Select “REV” when you mount the rotary commander on t...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories