If the system engages with the door in the open position, personal items that are left unattended in the garage or home are at risk to theft. To insure the safekeeping of these items, close the garage door. Typical signs of an engaged system: Single spring system: Visually inspect the TorqueMaster® Plus right hand end bracket to confirm that the system has engaged (see illustration). If the system is engaged then the door will not close. If the opener force settings were properly set during the

Press the counter gear onto the end bracket until snaps engage. Select the right hand counter cover assembly and align the hex of the counter cam with the end of the winding shaft. Also, align the “0” on the counter cover with the raised rib on the end bracket. Press the counter cover assembly against the counter gear until it locks into place. Repeat for left hand side for double spring applications. NOTE: No drive gear, counter gear or counter cover assembly is required on left hand side for s

This will prevent the door from raising or lowering while installing the rear support. Using perforated angle, 2” lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”-18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door. ^WARNING! KEEP HORIZONTAL TRACK PARALLEL AND WITHIN 3/4” OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN

IF THE INSERT SHEET INSTRUCTIONS ARE NOT INCLUDED, CONTACT WAYNE-DALTON CORP. FOR A FREE COPY. If removing an existing door, carefully follow the directions given on the insert sheet instruction in the portion titled “Removing the Old Door”. ¿^WARNING! REMOVAL OF AN EXISTING DOOR CAN BE DANGEROUS. FOLLOW INSERT SHEET INSTRUCTIONS CAREFULLY, OTHERWISE SEVERE OR FATAL INJURY COULD RESULT Begin the installation of the door by checking the opening. It must be the same size as the door. Vertical ja

NOTE: Do not tighten 1/4”-20 flange nuts to opener studs at this time. You will be instructed when to tighten them in the idrive® main installation and owners manual. Remove the temporary orange label holding the antenna wire. Straighten antenna wire and angle it 45 degrees to the right. NOTE: Do not coil the antenna wire. This will reduce the radio signal range. Power Drill 1/8” Drill Bit 7/16” Socket Driver 45 angle Antenna wire Mounting surface (Header) TOP OF DOOR SUPPORT BRACKET 1/4” X 1-1/

Plug the motor power cord into the opener. lEFT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED RIGhT haND END OF TORquEMasTER® sPRING TuBE RIGhT haND sIDE TORquEMasTER® sPRING TuBE aND BEaRING PROFIlEs alIGNED PluG-IN MOTOR POWER CORD MOTOR 17 Tools Needed: None Tools Needed: idrive® Installation NOTE: see idrive® main installation and owners manual for idrive® parts. IMPORTANT: RIGhT aND lEFT haND Is alWays DETERMINED FROM INsIDE ThE GaRaGE lOOkING OuT. lay the TorqueMaster® s

341785 REV1 08-03-2009 Low Head Room Front Mount Torsion Spring Installation Instructions and Owner’s Manual 9800 Series - 4 Section IMPORTANT NOTICE! Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. Wayne-Dalton Corp. P.O. Box 67 Mt. Hope, OH 44660 Definition of key words used in this manual: INDICaTEs a POTENTIally hazaRDOus sITuaTION WhICh

LIMITED WARRANT . The Manufacturer warrants that its door and its hardware fittings will be free from defect in workmanship and material. Should any defects in workmanship or material appea . within ONE YEAR of delivery, manufacture shall, upon notification, correct such nonconformity at its option, by repairing or replacing any defective part or parts. See maintenanc . and painting instructions for prepainted steel doors listed below or contact Wayne-Dalton Distributor for a copy of the mainten

x 3. sleeve anchors (precast). NOTE: Spring pads must be securely anchored before proceeding. The pads must by flush with the jambs. Attach the spring support brackets to the pad(s) using the following fasteners: Pre-Cast: Secure each spring support bracket using (2) 1/2. x 3. sleeve anchors. This installation will require the 1/2. anchors to be secured to the building, then securing the brackets to the anchors as detailed in Fig. N Page 11. Steel: Secure each spring support bracket using (3) 5/

1/2.- 5/8. 4. 1. OVERLAP 1. 1/2.- 5/8. 4. 1. 1/2.- 5/8. 4. FLUSH 1. 4. 4 3/4. 5/16 X 1. DRILLING / TAPPING SCREW 3/8 X 3. MIN. SLEEVE ANCHOR OPTIONAL MOUNTING BRACKET 5. OPTIONAL MOUNTING BRACKET 3/8 X 3. MIN. SLEEVE ANCHOR 5/16 X 1. DRILLING / TAPPING SCREW 2. X 6. JAMB IS RECOMENDED 1/2.- 5/8. 2 1/2. MIN. SIDE ROOM 1. OVERLAP 1 1/2. 1/2.- 5/8. 3 1/2. 1. OVERLAP 1 1/2. 1/2.- 5/8. 3 1/2. 1. OVERLAP 1 1/2. 1/2.- 5/8. 3 1/2. FLUSH 1 1/2. 3 1/2. 4 3/4. 5/16 X 1. DRILLING / TAPPING SCREW 3/8 X 3. MI