Log:
Téléchargements : 0   Taille : 8 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

341785 REV1 08-03-2009 Low Head Room Front Mount Torsion Spring Installation Instructions and Owner’s Manual 9800 Series - 4 Section IMPORTANT NOTICE! Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. Wayne-Dalton Corp. P.O. Box 67 Mt. Hope, OH 44660 Definition of key words used in this manual: INDICaTEs a POTENTIally hazaRDOus sITuaTION WhICh

Téléchargements : 3   Taille : 3 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

If in question about any of the procedures, do not perform the work. Instead, have a trained door systems technician do the installation or repairs. IMPORTANT SAFETY NOTICES An overhead door is a large heavy object that moves with the help of springs under high tension. Moving objects and springs under tension can cause injuries. For your safety and the safety of others, follow these instructions: 1. Wear protective gloves during installation to avoid possible cuts from sharp metal edges. 2. It

Téléchargements : 0   Taille : 3 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

WARNING WINDING BARS MUST FIT SNUGGLY INTO HOLES IN SPRING WINDING CONES. ATTEMPTING TO WIND SPRINGS WITH LOOSELY FITTING RODS, SCREWDRIVERS OR OTHER IMPROPER TOOLS CAN RESULT IN SEVERE OR FATAL INJURY. Feed the cable attached to the left hand bottom bracket up the vertical track, behind the rollers and secure to the left hand drum. Push the drum up against the end bearing bracket and secure to the shaft by tightening the set screws (solid shafts use 1/4” key(s) and set screws to secure drums).

Téléchargements : 1   Taille : 10 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

Press the counter gear onto the end bracket until snaps engage. Select the right hand counter cover assembly and align the hex of the counter cam with the end of the winding shaft. Also, align the “0” on the counter cover with the raised rib on the end bracket. Press the counter cover assembly against the counter gear until it locks into place. Repeat for left hand side for double spring applications. NOTE: No drive gear, counter gear or counter cover assembly is required on left hand side for s

Téléchargements : 0   Taille : 2 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

Attach to section using (2) 1/4”-20 x 7/8” self drilling screws at each end and center stile location. To attach a u-bar across the lower leaf of hinges with strut clips: Remove 1/4”-20 x 7/8” self drilling screws from lower leaf of hinges along sections which a u-bar will be attached to. Place u-bar above across hinges and attach to section with strut clips and the 1/4”-20 x 7/8” self drilling screws which were removed. 8300 LT-coM Aluminum Strutting Schedule---White, Almond, and Taupe colored

Téléchargements : 0   Taille : 2 mb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

Mark a vertical pencil line on the mounting surface above the door, at the center. Measure from the center of the bearing, in one of the end bearing brackets, downwards, to the top the door. Using that measurement, measure that distance upwards from the top of the door to the mounting surface, and mark a horizontal pencil line which intersects the vertical pencil line. Align the edge of the center bearing bracket with the vertical pencil line and the center of the bearing in the center bearing b

Téléchargements : 0   Taille : 107 kb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

Painting Your Garage Door suRfACE PREPARATION fOR PAINTING Wax on the surface must be removed or paint peeling/ flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad saturated with soapy water. A final wipe and rinse should be done with clean water only to remove any loose particles and any soapy film residue. Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or no. 4

Téléchargements : 0   Taille : 107 kb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the find a Dealer section online at Attaching hor Tracks to Q.I. flag Angles Tools: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder 14 NOTE: If you have Q.I. flag angles, complete this step. To install horizontal track, place the curved end over the top roller of the top section. Align key slot of the horizontal track with the Q.I. tab of the flag angle. Push curved portion of horiz

Téléchargements : 5   Taille : 107 kb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

Ensure the door rollers are rotating freely when opening and closing the door. If rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) hinges, steel rollers and bearings. DO nOT lubricate plastic idler bearings, nylon rollers, door track. DO nOT oil a cylinder lock, if actuation is difficult use a graphite dust to lubricate. 6 Please Do not Return This Product To The Store. Contact your local Wayne-

Téléchargements : 9   Taille : 768 kb   Fabricant : Wayne-Dalton  
Catégorie : Portail automatique
@name

This manual MUST be attached to the wall in close proximity of the door. WINDLOAD RATED DS-350 COMMERCIAL ROLL-UP DOORS INSTALLATION INSTRUCTIONS ©Copyright 2002 Wayne-Dalton Corp. P/N 291341, DOC #101-0093-1 REV 02 IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully before attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. 1. Operate the door ONLY when it is





catégories