Évaluations - 4, GPA: 3.5 ( )

Fabricant : Briggs & Stratton Taille : 4.64 mb Nom Fichier : ee457d4e-0940-42e3-8d8c-e73d028b893c.pdf Langue d'enseignement:

How To Change The Gear Reduction Oil -Figure 16 If your engine is equipped with a gear reduction unit, service as follows. 1. Remove the oil fill plug (B) and the oil level plug (C). 2. Remove the oil drain plug (A, Figure 16) and drain the oil into an appropriate receptacle. 3. Install and tighten the oil drain plug. 4. To refill, slowly pour gear lube into the oil fill hole (see Specifications section). Continue to pour until the oil runs out of the oil level hole. 5. Install and tighten the oil level plug. 6. Install and tighten the oil fill plug. Important: The oil fill plug has a vent hole (D) and must be installed on the top of the gear case cover as shown. How To Replace The Fuel Filter -Figure 17 WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. • Keep gasoline away from sparks, open flames, pilot lights, heat, and other ignition sources. • Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. • Before cleaning or replacing the fuel filter, drain the fuel tank or close the fuel shut-off valve. • Replacement parts must be the same and installed in the same position as the original parts. • If fuel spills, wait until it evaporates before starting engine. 1. Before replacing the fuel filter (A, Figure 17), if equipped, drain the fuel tank or close the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion. 2. Use pliers to squeeze tabs (B) on the clamps (C), then slide the clamps away from the fuel filter. Twist and pull the fuel lines (D) off of the fuel filter. 3. Check the fuel lines for cracks or leaks. Replace if necessary. 4. Replace the fuel filter with an original equipment replacement filter. 5. Secure the fuel lines with the clamps as shown. How To Clean The Air Cooling System -Figure 18 WARNING Running engines produce heat. Engine parts, especially muffler, become extremely hot. Severe thermal burns can occur on contact. Combustible debris, such as leaves, grass, brush, etc. can catch fire. • Allow muffler, engine cylinder and fins to cool before touching. • Remove accumulated debris from muffler area and cylinder area. NOTICE: Do not use water to clean the engine. Water could contaminate the fuel system. Use a brush or dry cloth to clean the engine. en This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to overheat, resulting in poor performance and reduced engine life. Use a brush or dry cloth to remove debris from the finger guard (A) (Figure 18). Keep linkage, springs and controls (B) clean. Keep the area around and behind the muffler (C) free of any combustible debris. Storage WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When Storing Gasoline Or Equipment With Fuel In Tank • Store away from furnaces, stoves, water heaters or other appliances that have pilot lights or other ignition sources because they can ignite gasoline vapors. Not for Reproduction Fuel System Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs & Stratton FRESH START® fuel stabilizer, available as a liquid additive or a drip concentrate cartridge. There is no need to drain gasoline from the engine if a fuel stabilizer is added according to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel system. The engine and fuel can then be stored up to 24 months. If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into an approved container. Run the engine until it stops from lack of fuel. The use of a fuel stabilizer in the storage container is recommended to maintain freshness. Engine Oil While the engine is still warm, change the engine oil. Troubleshooting Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723. Specifications EngineSpecificationsModel120000Displacement12.48ci(205cc) Bore2.688in(68.28mm) Stroke2.200in(55.88mm) OilCapacity18--20oz(0.54--0.59L) GearReductionOil80W-90EngineSpecificationsModel150000Displacement15.24ci(250cc) Bore2.970in(75.44mm) Stroke2.200in(55.88mm) OilCapacity18--20oz(0.54--0.59L) GearReductionOil80W-90EngineSpecificationsModel200000Displacement18.63ci(305cc) Bore3.120in(79.24mm) Stroke2.438in(61.93mm) OilCapacity26--28oz(0.77--0.83L) GearReductionOilSAE30EngineSpecificationsModel210000Displacement20.85ci(342cc) Bore3.300in(83.81mm) Stroke2.438in(61.93mm) OilCapacity26--28oz(0.77--0.83L) GearReductionOilSAE30 Tune-upSpecifications* Model120000,150000SparkPlugGap0.030in(0.76mm) SparkPlugTorque180lb-in(20Nm) ArmatureAirGap0.010-0.014in(0.25-0.36mm) IntakeValveClearance0.004-0.006in(0.10-0.15mm) ExhaustValveClearance0.009-0.011in(0.23-0.28mm) Tune-upSpecifications* Model200000,210000SparkPlugGap0.030in(0.76mm) SparkPlugTorque180lb-in(...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :