Évaluations - 3, GPA: 4.3 ( )

Fabricant : Briggs & Stratton Taille : 4.64 mb Nom Fichier : Langue d'enseignement:

Do not discard with household waste. Check with your local authorities, service center, or dealer for safe disposal/recycling facilities. Remove Oil 1. With engine off but still warm, disconnect the spark plug wire (A) and keep it away from the spark plug (Figure 10). 2. Remove the oil drain plug (B, Figure 11). Drain the oil into an approved receptacle. Note: Any of the oil drain plugs shown below may be installed in the engine. Not for Reproduction 3. After the oil has drained, install and tighten the oil drain plug. Add oil • Place engine level. • Clean the oil fill area of any debris. • See the Specifications section for oil capacity. Models with oil fill cap 1. Remove the oil fill cap (D, Figure 11). 2. Pour the oil slowly into the engine oil fill (E). Fill to point of overflowing. 3. Replace and tighten the oil fill cap. Models with short dipstick 1. Remove the dipstick (F, Figure11) and wipe with a clean cloth. 2. Pour the oil slowly into the engine oil fill (E). Fill to point of overflowing. 3. Install the dipstick but do not screw in. Remove and check the oil level. Oil level should be at the FULL mark (G) on the dipstick. 4. Install and tighten the dipstick. Models with extended dipstick 1. Remove the dipstick (F, Figure 12) and wipe with a clean cloth. 2. Pour the oil slowly into the engine oil fill (E). Do not overfill. After adding oil, wait one minute and then recheck the oil level. 3. Install and tighten the dipstick. 4. Remove the dipstick and check the oil level. It should be at the top of the full indicator (G) on the dipstick. 5. Install and tighten the dipstick. How To Service The Air Filter -Figure 141513 WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. • Never start or run the engine with the air cleaner assembly (if equipped) or the air filter (if equipped) removed. 1. Loosen the fastener (D) that holds the cover (A). 2. Open the cover and remove the pre-cleaner (C) and the filter (B). 3. To loosen debris, gently tap the filter on a hard surface. If the filter is excessively dirty, replace with a new filter. 4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air dry. Do not oil the pre-cleaner. 5. Assemble the dry pre-cleaner to the filter with the lip (G) of the pre-cleaner on the bottom of the filter pleats. 6. Install the filter. 7. On models equipped with air filter shown in Figure 13, install the cover tabs (E)into the slots (F). 8. Close the cover and secure with the fastener. Oval Air Filter (Figure 15) 1. Loosen the fastener (D) that holds the cover (A). 2. Open the cover and remove the pre-cleaner (C) and the filter (B). 3. Remove the pre-cleaner (C), if equipped, from the filter. To loosen debris, gently tap the filter on a hard surface. If the filter is excessively dirty, replace with a new filter. 4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air dry. Do not oil the pre-cleaner. 5. Assemble the dry pre-cleaner to the filter. 6. Install the filter and pre-cleaner into the base (E) and onto stud (F). Make sure filter fits securely into base. 7. Install air filter cover and secure with the fastener. Make sure the fastener is tight. How To Change The Gear Reduction Oil -Figure 16 If your engine is equipped with a gear reduction unit, service as follows. 1. Remove the oil fill plug (B) and the oil level plug (C). 2. Remove the oil drain plug (A, Figure 16) and drain the oil into an appropriate receptacle. 3. Install and tighten the oil drain plug. 4. To refill, slowly pour gear lube into the oil fill hole (see Specifications section). Continue to pour until the oil runs out of the oil level hole. 5. Install and tighten the oil level plug. 6. Install and tighten the oil fill plug. Important: The oil fill plug has a vent hole (D) and must be installed on the top of the gear case cover as shown. How To Replace The Fuel Filter -Figure 17 WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. • Keep gasoline away from sparks, open flames, pilot lights, heat, and other ignition sources. • Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. • Before cleaning or replacing the fuel filter, drain the fuel tank or close the fuel shut-off valve. • Replacement parts must be the same and installed in the same position as the original parts. • If fuel spills, wait until it evaporates before starting engine. 1. Before replacing the fuel filter (A, Figure 17), if equipped, drain the fuel tank or close the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion. 2. Use pliers to squeeze tabs (B) on the clamps (C), then slide the clamps away from the fuel filter. Twist and pull the fuel lines (D) off of the fuel filter. 3. Check the fuel lines for cracks or leaks. Replace if necessary. 4. Replace the fuel filter with an orig...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :