Log:
Téléchargements : 21   Taille : 514 kb   Fabricant : Kenwood  
Catégorie : Vidéo de voiture
@name@name@name@name@name@name@name

Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C. 2CAUTION Thoroughly wipe away and dust or grease from the installation location using a cloth which has been soaked in a neutral cleaning agent and wrung out. Attach the stand after allowing the installation location to dry. 1 Bend the stand support to conform to the shape of the installation location. 2 Adjust the shape of the support so that th

Téléchargements : 0   Taille : 598 kb   Fabricant : Audiovox  
Catégorie : Vidéo de voiture
@name

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-15 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 18 GA wire 4' 8. Audiovox Series 640/650 Video Module

Téléchargements : 7   Taille : 2 mb   Fabricant : Boss Audio Systems  
Catégorie : Vidéo de voiture
@name

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials / Tools required for this installation: 1. Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or scribe point tool or similar 4. Razor knife or similar tool 5. T-10TORX bit driver 6. 1/8" Drill Bit 7. Audiovox Series 640/650 Video Module FOR

Téléchargements : 0   Taille : 2 mb   Fabricant : Carson Optical  
Catégorie : Vidéo de voiture
@name

Set assembly aside in a safe place for re-use later. 3. Remove center A/C vent in headliner using two scribe points in indicator holes on vent and twist. II. PREPARATION OF VEHICLE. 1. Place template provided (item 12 pg 2) over center A/C vent hole with arrow pointing forward. Cut and remove indicated headliner. See Figure 1. 2. Install plywood block (item 18 pg 2) provided in kit through modified louver opening and secure in place using two (2) # 8 x 9/16" PWH screws (item 3 pg2). See Figure 2

Téléchargements : 1   Taille : 2 mb   Fabricant : Boss Audio Systems  
Catégorie : Vidéo de voiture
@name

See Fig. 8. 2. Remove and retain secondary light and pod assembly by removing eight ( 8 ) OEM screws. See Figure 9. Figure 8 Figure 9 6 3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of bezel with four (4 ) 6-32 X 1/2" screws (item 4 pg 2) and four (4) 8-32 KEPS nuts (item 1 pg 2). See Figure 10. Figure 10 4. Install and secure O.E. bezel in overhead console (item 19 pg 2) with eight ( 8 ) # 6 X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. Figure 11 7 5. Rem

Téléchargements : 0   Taille : 2 mb   Fabricant : Carson Optical  
Catégorie : Vidéo de voiture
@name

2. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 5 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. Inspect wiring to make sure no chaffing has occurred near the rear bracket (Item 3). 3. Secure front of console using one ( 1 ) # 8 X 1 1/2" PWH screw (item 7) in front pocket of

Téléchargements : 1   Taille : 1 mb   Fabricant : Audiovox  
Catégorie : Vidéo de voiture
@name

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-45 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 7/64" drill bit 8. Small chisel 9. Audiovox Series 64

Téléchargements : 0   Taille : 1 mb   Fabricant : Audiovox  
Catégorie : Vidéo de voiture
@name

dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure O.E.M. ground wire (if applicable) using one of the screws. See Figure 8. FIGURE 8 6 8. If vehicle is equipped with an electronic compass, un

Téléchargements : 0   Taille : 1 mb   Fabricant : Audiovox  
Catégorie : Vidéo de voiture
@name

Failure to do so may cause damage to console or installed components. Figure 16 2. Raise overhead console into approximate position and connect wiring to O.E. components. 3. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 10 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. See Fi

Téléchargements : 0   Taille : 555 kb   Fabricant : Audiovox  
Catégorie : Vidéo de voiture
@name

Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Digital Volt Meter 5. 18 GA wire 9' 6. Rubbing Alcohol 7. 5/16” Hex Socket Bit 8. Razor knife or similar 9. Pencil or equivalent 10. Measuring tape 11. Masking tape 12. Audiovox Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF. 128-6067 Text Box: Feb. 13,2001 Printed in the U.S.A Text Box: INSTALLATION INSTRUCTION # 44-00





catégories