Évaluations - 7, GPA: 4.6
(
)
)
|
Photos et spécifications Makita UC3020A |
Facilité d'utilisation
Brugsanvisning Bruksanvisning Bruksanvisning Kayttoohje ...... ..... UC3020A UC3520A UC4020A 2 1 2 3 4 1 2 3 4 5 6 7 13 11 9 8 10 12 15 14 2 1 3 5 6 7 8 9 10 11 12 1 2 3 4 5 6 29 7 8 9 10 3 11 4 12 3 4 4 13 14 15 16 17 18 19 20 13 14 6 15 16 2-4mm 3 11 Reclaimend oil 17 13 14 6 15 16 2-4mm 1 2 18 19 20 21 22 21 22 21 22 A B A B 23 24 45o 2 1/2 45o 23 25 26 27 28 a a a 0.5 mm 0.5 mm min. 3 mm a a a 0.5 mm 0.5 mm min. 3 mm 0 80 80 31 32 30 33 34 24 25 35 36 27 26 27 26 28 37 38 28 39 40 26 29 41 42 ENGLISH ENGLISH 1. Rear handle 6. Guide bar 11. Rear hand guard 2. Switch trigger 7. Saw chain 12. Serrated rail (claw stop) 3. Oil filter cap 8. Lever 13. Lock-off button 4. Front handle 9. Sprocket cover 14. Chain catcher 5. Front hand guard 10. Oil level sight 15. Scabbard Explanation of general view 1. Lock-off button 11. Tighten 21. Sight glass 2. Switch trigger 12. Lever 22. Serrated rail 3. Press in 13. Low 23. Felling area 4. Loosen 14. High 24. Oil guide groove 5. Sprocket cover 15. Guide bar 25. Oil feed hole 6. Adjusting dial 16. Saw chain 26. Push nut 7. Adjusting pin 17. Oil filler cap 27. Slotted bit screwdriver 8. Hook 18. Hand guard 28. Filter 9. Hole 19. Lock 29. Sprocket 10. Small hole 20. Unlock SPECIFICATIONS Model UC3020A UC3520A UC4020A Max. chain speed (m/s) 13.3 Cutting length 300 mm 350 mm 400 mm Saw chain Type 90SG Pitch 3/8” Acoustic power level L WA av dB (A) to EN 50144 -1 1) 105.3 Sound pressure level L pA av dB (A) at the workplace to EN 50144 -1 1) 92.3 Vibration acceleration a h,w av to ISO 50144-2-13 1) - Front handle m/s2 3.4 3.9 - Rear handle m/s2 4.0 4.5 Oil pump Automatic Oil tank capacity (l) 0.20 Power transmission Direct Chain brake Manual Run-down brake Mechanical Overall length (without guide bar) 436 mm Net weight 3.8 kg Extension cable (optional) DIN 57282/HO 7RN -F L=30 m max., 3 x 1.5 mm2 1) The data assign equal weight to the full-load and maximum speed operating conditions. • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country. Symbols END218-1 .................... DOUBLE INSULATION The following show the symbols used for the tool. Be sure that you understand their meaning before use. ................... Caution: particular care and attention required! .................. Read instruction manual and follow the warnings and safety instructions. ................... Caution: withdraw the mains plug immediately if the cable is damaged! ! ................... Protect against rain and damp! ................... Wear a helmet, goggles and ear protection! ................... Wear safety gloves! ................... Withdraw the mains plug! ................... First aid RE Y ......... Recycling ................... CE marking ........... Maximum permissible length of cut .......... Direction of chain travel ................... Chain oil ............. Chain brake released/applied ................... Prohibited! Intended use The tool is intended for cutting lumbers and logs. Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire. For public low-voltage distribution systems of between 220 V and 250 V. Switching operations of electric apparatus cause voltage fluctuations. The operation of this device under unfavorable mains conditions can have adverse effects to the operation of other equipment. With a mains impedance equal or less than 0.35 Ohms it can be presumed that there will be no negative effects. The mains socket used for this device must be protected with a fuse or protective circuit breaker having slow tripping characteristics. ADDITIONAL SAFETY RULES ENB098-1 1. Read the instruction manual in order to familiarize yourself with operation of the chain saw. 2. Before using the chain saw for the first time, arrange to have instruction in its operation. If this is not possible, at least practice cutting round timber on a trestle before beginning work. 3. The chain saw must not be used by children or young persons under 18 years of age. Young persons over 16 years of age may be exempted from this restriction if they are undergoing training under the supervision of an expert. 4. Working with the chain saw requires a high level of concentration. Do not work with the saw if you are not feeling fit and well. Carry out all work calmly and carefully. 5. Never work under the influence of alcohol, drugs or medication. Proper use 1. The chain saw is intended solely for cutting wood. Do not use it for example to cut plastic or porous concrete. 2. Only use the chain saw for operations described in this instruction manual. Do not, for example, use it to trim hedges or for similar purposes. 3. The chain saw must not be used for f...
Ce manuel est également adapté pour les modèles :Benzo et scies - UC3520A (2.01 mb)
Benzo et scies - UC4020A (2.01 mb)